« previous next »
Pages: 1 ... 4 5 [6] 7 8 ... 13   Go Down

Author Topic: project onion rings  (Read 33047 times)

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #75 on: March 25, 2020, 07:12:52 PM »
....
Logged

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #76 on: March 25, 2020, 07:17:05 PM »
I even fabricated the original seat belt bracket, (Toyota) to accept the GM latch.
« Last Edit: March 25, 2020, 07:20:05 PM by chevn-up »
Logged

Offline Mike81K10

  • Junior Member
  • ***
  • Posts: 909
Re: project onion rings
« Reply #77 on: March 25, 2020, 09:20:53 PM »
Looking Nice, I like alot of what you have done.
Logged
"Tell me and I forget. Teach me and I remember. Involve me and I learn." -Benjamin Franklin

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #78 on: March 26, 2020, 06:42:25 PM »
Thanks. When the truck was my dd, I would slip and slide on the vinyl bench seat. After the buckets install, with the cloth and side support, there is so much better control of the vehicle.
Logged

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #79 on: March 26, 2020, 07:03:35 PM »
Picked this tranny cover from a 77 K10.
Logged

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #80 on: March 26, 2020, 07:11:37 PM »
Sandblasted for a quick clean-up
Logged

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #81 on: March 26, 2020, 07:15:52 PM »
 I needed the cover for the ginormous hole in the floor, plus it looks really cool.
Logged

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #82 on: March 26, 2020, 07:19:04 PM »
Made this transition piece to "blend" into the floor.
Logged

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #83 on: March 26, 2020, 07:23:18 PM »
Cool. Control for my 350C, which was another can of worms.
Logged

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #84 on: March 28, 2020, 05:30:28 AM »
My tank relocate was fun. Just be sure to level it at ride height. It's a 25 gallon, although I had to use the 31 gal. straps to get it low enough in the chassis for the filler tube to be ok. Gravity is a wonderful thing.
Logged

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #85 on: March 28, 2020, 05:32:28 AM »
The filler door.
Logged

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #86 on: March 28, 2020, 05:34:08 AM »
another shot
Logged

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #87 on: March 28, 2020, 05:50:20 AM »
The filler tube is from a suburban. I believe the 81-87 tubes are a different size than previous years? Be aware of that.
« Last Edit: March 28, 2020, 05:54:10 AM by chevn-up »
Logged

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #88 on: March 28, 2020, 06:03:16 AM »
Ordered this flexible connector hose from across the creek on the internet. 17 pounds, which equals 37 US dollars. And yes, it is for fuel.
Logged

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #89 on: March 28, 2020, 06:09:13 AM »
And last is the cover. The red one was the best I could find, until I found a new one. Guess which one I'm using......
Logged
Pages: 1 ... 4 5 [6] 7 8 ... 13   Go Up
« previous next »