73-87chevytrucks.com

73-87 Chevy _ GMC Trucks => Performance => Topic started by: 1979C20 on June 12, 2014, 11:10:17 PM

Title: Gathering parts for a turbo build. Need some advice
Post by: 1979C20 on June 12, 2014, 11:10:17 PM
So here is the motor in my Suburban. http://www.jegs.com/i/GM-Performance/809/19210007/10002/-1?parentProductId=1231165

The only thing that isnt the same on this motor is the heads. It has the stock TBI heads on it. Im tracking down the parts to turbo charge it, either a 76mm turb or two smaller ones, not sure what I can get ahold of yet. Im just  curious, what would you recommend for max boost on the internals listed.
Title: Re: Gathering parts for a turbo build. Need some advice
Post by: Irish_Alley on June 13, 2014, 12:02:13 AM
you can get a better motor for 3k
https://www.yearone.com/Product/1967-87-chevy-gmc-truck/ct350pc1
Year One Power Crate 400hp 350 crate engine assembly.
Engine Specifications:
* Horsepower: 400+
* Torque: 400+ ft/lbs
* Compression ratio: 9.7:1
* Dyno-tested: Yes, includes 8" balancer & 14" flexplate
* Dyno sheet: Included with engine's output
* Vacuum produced: 12hg @ 800RPM
* Recommended fuel: 92 octane
* Max recommended RPM- 5800
* Block: Seasoned 4-bolt iron
* Crankshaft: OE cast iron
* Pistons: Hypereutectic
* Connecting rods: Powdered metal
* Camshaft- Hydraulic roller with YearOne proprietary specifcations
* Rocker arms: Stamped steel 1.6:1 ratio
* Cylinder heads: Ported Dart Iron Vortec
* Valves: Stainless steel 2.02 int/1.60 exh
* Valve springs: Heavy duty
* Bore x Stroke: 4.04" x 3.48"
* Intake manifold: Dual-plane aluminum
* Oil pan, timing cover, valve covers included
* Engine fasteners: High tensile strength
* Warranty: 12 mth/12,000 mi
i dont know anything about turbos
Title: Re: Gathering parts for a turbo build. Need some advice
Post by: 1979C20 on June 13, 2014, 09:23:36 PM
Irish, that motor I listed is the motor that is already in the truck from when I bought it.
Title: Re: Gathering parts for a turbo build. Need some advice
Post by: Irish_Alley on June 13, 2014, 10:36:24 PM
lmao oh my bad, continue on then.
Title: Re: Gathering parts for a turbo build. Need some advice
Post by: 1979C20 on June 14, 2014, 09:53:44 PM
Can anyone chime in on mac recommended PSI? I was thinking 7 pr 8...
Title: Re: Gathering parts for a turbo build. Need some advice
Post by: Stewart G Griffin on June 15, 2014, 11:56:51 PM
What's the compression with the TBI heads?
Title: Re: Gathering parts for a turbo build. Need some advice
Post by: 1979C20 on June 16, 2014, 05:11:36 AM
I believe 8.75:1, but it could be 9.1:1.   TBI heads cam with either 64cc or 65cc chambers, so im not entirely sure. How could I test? Compression test?
Title: Re: Gathering parts for a turbo build. Need some advice
Post by: Captkaos on June 17, 2014, 01:11:28 AM
That motor is 9.1:1 if it is identical to what you posted.  How do you plan on turboing it?  What are you doing for fuel delivery?
I would cap it at around 5-7 to be safe.
Title: Re: Gathering parts for a turbo build. Need some advice
Post by: 1979C20 on June 17, 2014, 05:20:57 PM
I know I need a larger fuel pump, and I was planning on a vacuum fuel pressure reg.
Title: Re: Gathering parts for a turbo build. Need some advice
Post by: 1979C20 on August 08, 2014, 03:35:28 AM
I found a AR.48 t3 turbo off a 88 tbird. Im curious if this would alright?
Title: Re: Gathering parts for a turbo build. Need some advice
Post by: HAULIN IT on August 08, 2014, 06:24:32 PM
Two of them would be the beginning of something, one? No way! 
Title: Re: Gathering parts for a turbo build. Need some advice
Post by: Captkaos on August 17, 2014, 01:37:17 PM
Ditto.  and if you want to feed them carb fuel you need to talk to Lorne.