73-87chevytrucks.com

Welcome to 73-87chevytrucks.com

73-87chevytrucks.com is not only a forum we are also a vendor for a variety of parts both replacement and custom. Check out our store at 73-87chevytrucks.com Online Store

73-87chevytrucks Social Network

We are also on Facebook so give us a like to the page if you like what you see: http://www.facebook.com/7387chevytrucks

73-87chevytrucks Merchandise

SpreadShop Site

Cafepress Site

Does anyone know part number for carrier bearing and rubber boot

June 23, 2025, 04:43:25 am by plow_truck
Views: 346 | Comments: 9

Does anyone know what correct carrier bearing and whether there is an appropriate rubber boot?

I'm in the process of replacing the carrier bearing and it looks to me like there should be some sort of boot to cover the open spline.

The u-joints are spicer 1350 series (1.188 OD x 3.63 end to end) and the carrier bearing is 1.574 at the bearing with a 1.500 dia spline.

Its a 1979 K30 with SM465 transmission and a 454 that was swapped in, also its got 4.56 gears.

I'm going through the dana / spicer catalog and theres a handful of these (carrier bearing) that come up under style 15 with 1.574 ID, 6.62 bolts to mount and 2.25 dim from bottom to bearing center... but they have different front slinger / rear slinger. If those are the pieces on the end, then I want to replace them if I can.

Read More | Write Comment

Intermittent wipers not working on 83.

June 22, 2025, 12:03:45 pm by slideways | Views: 130 | Comments: 1

So finally getting some miles under this newly redone K10. I had to get a new wiper motor because the pump quit. I noticed that the wipers work fine on low/high but they dont work on intermittent. I assume that twisting the little knob is supposed to change the frequency of wipe? It doesnt seem to do anything. Is there a typical failure here?

Thanks

Read More | Write Comment

Ground connection on instrument cluster

June 20, 2025, 10:16:30 am by greenacres | Views: 341 | Comments: 7

I have been working on my 1979 Chevy K10. I have progressed to the point that I am ready to install the instrument cluster and dash. The ground wire that goes to the instrument cluster was missing when I got this truck back from the body shop, but I can easily make a new ground wire.

I have looked and looked and I can’t find anyplace on the instrument cluster to connect a ground wire. Can someone please tell me where the ground connection is on the back of the instrument cluster?

I don’t know if this makes any difference or not, but the body shop replaced the cab and I think it is from a 1977 C10. I don’t know which cab the instrument cluster is from, and I am not on speaking terms with that body shop.

Read More | Write Comment

Rear axle is 7/16” off center

June 09, 2025, 05:49:42 am by Lowellguy1 | Views: 8261 | Comments: 1

Hello, I have a 87 R10 (rear axle flip) with a 12 bolt (5 lug) that I cannot verify it’s part number because it isn’t located where it should be. This leads me to believe it could have been a swap from another gm vehicle. All mounts are oe and the locations are centered (based on the C/L) of the pinion. When I compare the inside distance from the tire to the frame rail they differ by almost 7/16” It might seem minor but I have the widest wheel possible to tuck in there with the stock wheel well and it is almost hitting the bolts on the inside (drivers side). Yes the bed is squared and centered on the frame rails.

Any suggestions are always appreciated.
Thanks

Sent from my iPhone using Tapatalk

Read More | Write Comment

Header recommendations for 305

June 08, 2025, 02:40:16 pm by Rough75C20
Views: 6610 | Comments: 1

Hello,

Looking into headers for my 305. Any recommendations? Currently looking at headers from summit racing and jegs. I’ve read to stay with a little smaller diameter for clearance issues. Would like to buy a set that I don’t have to beat with a hammer too much to get to fit. Current setup is a 75 2wd c20 with a 305 out of an 86. Would like to stay under 500 dollars if possible. Would like to keep the temp sensor in the side of the block on the drivers side which I’ve read have had clearance issues in the past. Let me know your thoughts.

Thank you

Sent from my iPhone using Tapatalk

Read More | Write Comment

Pages: [1]