Author Topic: project onion rings  (Read 35259 times)

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #150 on: April 11, 2023, 03:51:42 AM »
same size, single row...29x20 core, overall length 33 1/2. plastic ends. Took a little searching the net to find. Matches the rubber bushings and upper brackets also.

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #151 on: April 30, 2023, 10:03:12 AM »
Installed the front side lines of the cooler. Used NBR hose. Should be ok.

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #152 on: April 30, 2023, 10:07:28 AM »
Also, finished with the front wire harness. All new bulb sockets. Everything soldered, as well as dielectric grease and shrink-wrap on all splices. Pert near new again.

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #153 on: April 30, 2023, 10:08:50 AM »
Now to start on these.

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #154 on: June 24, 2023, 08:02:03 PM »
ok, all fab and painting done.

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #155 on: June 24, 2023, 08:04:41 PM »
wow, guess I need to figure-out my camera /re sizing options.

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #156 on: June 24, 2023, 08:06:33 PM »
here it is, I hope

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #157 on: June 24, 2023, 08:07:50 PM »
..

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #158 on: June 24, 2023, 08:08:48 PM »
turns out the camera more work than truck.   sorry

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #159 on: June 25, 2023, 11:40:59 AM »
bagged and tagged all the bolts and shims, so it should go back together ok.

Offline JohnnyPopper

  • Senior Member
  • ****
  • Posts: 2566
  • Old Goof
Re: project onion rings
« Reply #160 on: June 25, 2023, 05:10:42 PM »
Looking good brother!!! ;)
1957 Apache 3100 235 Inline 6, 3 on the tree
1973 C-20, 3+3 454 4BBL TH400  Water Injection
1978 K-10, 350 4BBL TH350 NP203 M.M. Part time Kit/Hubs
1980 C-10 under construction

Offline Shifty

  • Junior Member
  • ***
  • Posts: 978
  • I bleed Bowtie red...
Re: project onion rings
« Reply #161 on: June 26, 2023, 10:35:11 AM »
Excellent!  8)
87 V20 Standard Cab Longbed (current)

87 R30 3+3 Longbed (days of yore)

98 C2500 ext cab longbed

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #162 on: July 04, 2023, 07:55:12 AM »
Finished grafting the front wire harness back in..... It's alive!

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #163 on: July 04, 2023, 07:57:33 AM »
got everything to finish the front, in due time

Offline chevn-up

  • Registered Users
  • *
  • Posts: 171
  • Newbie
Re: project onion rings
« Reply #164 on: July 04, 2023, 08:12:30 AM »
Time to get these back in. Delivered the driveshaft to my local driveline shop for new parts and a speed balance. Gonna finish up with the radiator install, and then I will fill her with fluids and maybe putt around the neighborhood.
« Last Edit: July 04, 2023, 08:15:02 AM by chevn-up »