73-87chevytrucks.com

Welcome to 73-87chevytrucks.com

73-87chevytrucks.com is not only a forum we are also a vendor for a variety of parts both replacement and custom. Check out our store at 73-87chevytrucks.com Online Store

73-87chevytrucks Social Network

We are also on Facebook so give us a like to the page if you like what you see: http://www.facebook.com/7387chevytrucks

73-87chevytrucks Merchandise

Cafepress site

Spreadshirt site

Wide steel rims that accept dogdish caps

March 21, 2025, 07:21:44 am by Swampyankee74
Views: 243 | Comments: 3

Hello everyone, I am looking for some stock looking rims either 15x9 or 15x10 4.25-4.5 backspacing with a 5x5 bolt patern that accepts the stock dogdish up caps. I can find 15x8 in that style. But would like to go wider to accept 295/50-15 tires. Any info would be helpful.

Read More | Write Comment

new 20 gallon tank

March 11, 2025, 05:59:31 pm by Rough75C20
Views: 3701 | Comments: 5

Hello All,

Looking to upgrade my C20 Fuel system. I currently have a 14-gallon tank on the passenger side that is being used as the main tank. However, the sending unit isn't hooked up to the gauge so I'm guessing on gas level right now. I am looking at getting a new 20-gallon tank from Jegs. Question is about the fuel sending unit. the truck currently has a 305 with a 4-barrel Quadrajet. I'm looking at the fuel sending units and I believe I need the one with two outlets (supply and vent). I haven't seen a return line to the current tank. Is this normal for these old carb setups? I have attached what is currently in my shopping cart from Jegs. Let me know your thoughts. I'm planning on using a T with a ball valve to control which tank is being used, but the sending unit will be hooked up to the main tank.

Read More | Write Comment

Power window and lock conversion with harness connections inside cab

March 05, 2025, 09:49:09 am by Lowellguy1 | Views: 4381 | Comments: 1

Hello, I am restoring an 1987 Chevy R10. I am converting it to power windows and locks from donor doors. I have acquired an original door harness for each side. When I ran the harness through A Plr. and into the cab on the passengers side there was an existing 6 plug female block/connector above the glovebox that looked to be correct for the passengers side harness. Is this possible it is pre wired for these options? On the drivers side I could not find the same plug. (I have yet to verify the plug and power on the passengers side). I did remove a doner harness a while back but my issue is that the plugs on each end of the donor (cab) harness are not correct. Any help with locating the schematics as to how each side ties into the dash harness would be greatly appreciated.

Read More | Write Comment

76 k20 overlanding rig

February 26, 2025, 06:39:43 pm by 1989bmw535i | Views: 3953 | Comments: 3

I'm attempting to do something not a lot of people have done in one of these trucks, I plan to drive the pan-american highway. I'll start in Prudhoe bay Alaska and end in Argentina, although I'll probably see how far I can make it south in Chile, I'm not following the highway, I'm gonna float around where ever I feel and in south America and Mexico I'll probably zig zag from coast to coast. I have a 76 chevy k20, it currently has a 350/th400 with a 10 bolt front end, 14 bolt rear and an np208 transfer case. I plan to swap it for a lightly modified 24v common rail cummins, I'll keep the axles, and find a manual transmission and transfer case (probably an np205) to fit the cummins, I'm only choosing the cummins for reliability, I need it to be capable of running high sulfer fuel and I'm going to "bulletproof" it. I'm going to take the bed off and build a camper on the back, I'm looking at 35in tires and a 4in lift. For those who are unfamiliar, some of the roads in south America are straight up offroad trails and I need the vehicle to be capable but also dependable, I'll probably be gone for 1.5-2 years. I'm looking for any advice people have to get the truck to a point I don't have to worry about it, what suspension can I get that will flex some but still be able to handle the weight of the camper? Any advice is appreciated. Thanks!

Read More | Write Comment

73-87Chevytrucks.com Hosting update

February 17, 2025, 05:18:33 pm by Captkaos
Views: 10793 | Comments: 17

In the next few days we will be migrating all pages from 73-87chevytrucks.com to a new Hosting platform with new servers and hardware. Prior to this happening the forum will be put in maintenance mode were we can freeze it for the migration and not loose any post. Please bear with us while this work is done as it may be an hour or more for the update to be completed.

If you have any questions please email us at webmaster@73-87chevytrucks.com

Read More | Write Comment

Pages: [1]