Author Topic: Top shock hole wallowed, go inboard?  (Read 2915 times)

Offline 4inthefloor

  • Newbie
  • Posts: 8
  • Newbie
Top shock hole wallowed, go inboard?
« on: March 24, 2019, 04:27:54 PM »
I recently discovered the top shock bolt loose on my 84 3/4 ton suburban. I'll  attach a picture of it. There's no cracks, but I'm wondering. I've been thinking of moving my shocks in board, but looking for suggestions on the wallowed hole. Should I just clean it up/paint it and leave it alone or is there any repairs I should do to the hole, what's the likelihood of it developing a crack without the shock beating on it?


Offline cffisher

  • Newbie
  • Posts: 23
  • Newbie
Re: Top shock hole wallowed, go inboard?
« Reply #1 on: April 11, 2019, 05:36:59 PM »
I think I would plug the hole then redrill it to fit. Plug it with same thickness material, and weld in.
Retired and loving it.

Offline roundhouse

  • Senior Member
  • ****
  • Posts: 1474
  • Newbie
Re: Top shock hole wallowed, go inboard?
« Reply #2 on: April 12, 2019, 06:47:47 AM »
Could weld a thick washer on each side

Easier than plugging and drilling

Offline JohnnyPopper

  • Senior Member
  • ****
  • Posts: 2526
  • Old Goof
Re: Top shock hole wallowed, go inboard?
« Reply #3 on: April 12, 2019, 12:36:35 PM »
Drill another hole to the right about 1" and get it back on the road!

Prime and paint the oblong hole.

There, fixed it.
1957 Apache 3100 235 Inline 6, 3 on the tree
1973 C-20, 3+3 454 4BBL TH400  Water Injection
1978 K-10, 350 4BBL TH350 NP203 M.M. Part time Kit/Hubs
1980 C-10 under construction

Offline 4inthefloor

  • Newbie
  • Posts: 8
  • Newbie
Re: Top shock hole wallowed, go inboard?
« Reply #4 on: April 12, 2019, 06:29:14 PM »
Good ideas, from all of you guys. I'm gonna weigh my options, not in a real hurry as it's just sitting around right now after an engine swap and finishing up the fuel system.  But I wanted to get some more eyes and opinions about it. Thanks

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 18979
Re: Top shock hole wallowed, go inboard?
« Reply #5 on: April 12, 2019, 06:40:35 PM »
Could weld a thick washer on each side

This
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline blazer74

  • Junior Member
  • ***
  • Posts: 786
  • Newbie
Re: Top shock hole wallowed, go inboard?
« Reply #6 on: April 15, 2019, 04:09:08 AM »
Weld thick washers then get the shock bolt reinforcement brackets or make them. Do an internet search.

Offline Stewart G Griffin

  • Senior Member
  • ****
  • Posts: 3324
Re: Top shock hole wallowed, go inboard?
« Reply #7 on: April 15, 2019, 01:12:23 PM »
What causes this?   i had the same problem on the rear control arms/trailing(?) arms of a GM FWD car.

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 18979
Re: Top shock hole wallowed, go inboard?
« Reply #8 on: April 15, 2019, 05:52:21 PM »
Loose shock mount
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10