« previous next »
Pages: [1]   Go Down

Author Topic: fiberglass hood  (Read 4673 times)

Offline 808SS

  • Newbie
  • Posts: 52
fiberglass hood
« on: March 06, 2009, 01:15:39 pm »
Just need alittle help, the hood came with the truck but I notice when I open the hood the springs are gone so I have to hold the hood up with a stick. Is there a reason not to use the springs with the fiberglass hood?
Logged
1979 C10, airride, 20" rims, and lots of rust
1994 Impala SS, under construction, LSX, 4L80E, 4.10 gears, sound system, 20" rims up front and 22" rims rear

Offline choptop

  • Senior Member
  • ****
  • Posts: 2476
  • Extended cab fanatic
    • conversiontrucks
Re: fiberglass hood
« Reply #1 on: March 06, 2009, 01:22:54 pm »
Most are too flimsy to handle compressing the springs. I plan on putting the little hydraulic shocks used on newer cars and hatchbacks to hold mine up. For now, just a prop rod.
Logged
76 C10 Choptop,76 C10 Swb
85 C10, 85 K10, 85 K20,86 C10,86 K10 (all extended cabs)
86 C30 extended crewcab

Offline 808SS

  • Newbie
  • Posts: 52
Re: fiberglass hood
« Reply #2 on: March 06, 2009, 02:17:37 pm »
I was thinking that was the problem just need to hear it from someone else. let me know about that little hydraulic shock
Thanks guys
Logged
1979 C10, airride, 20" rims, and lots of rust
1994 Impala SS, under construction, LSX, 4L80E, 4.10 gears, sound system, 20" rims up front and 22" rims rear

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19181
Re: fiberglass hood
« Reply #3 on: March 06, 2009, 03:39:45 pm »
you need low tension springs or a prop rod. Just another reason why fiberglass is a pita. What year is your truck?
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline cubicdollars

  • Frequent Member
  • **
  • Posts: 345
Re: fiberglass hood
« Reply #4 on: March 06, 2009, 03:40:26 pm »
What I have seen people do in the past is drill a hole through both sides of the hing while the springs are still attached then remove the springs. When you raise the hood you then place a pin or bolt through the hole. So much easier and safer than dragging a prop rod around.

Hope this helps
Logged
1977 Stepside,F2 Procharged BBC 505
1984 Buick T Type Regal, LS Swapped

Offline 808SS

  • Newbie
  • Posts: 52
Re: fiberglass hood
« Reply #5 on: March 06, 2009, 05:15:05 pm »
Quote from: VileZambonie on March 06, 2009, 03:39:45 pm
you need low tension springs or a prop rod. Just another reason why fiberglass is a pita. What year is your truck?

79' any idea or part# for the low tension spring?
Logged
1979 C10, airride, 20" rims, and lots of rust
1994 Impala SS, under construction, LSX, 4L80E, 4.10 gears, sound system, 20" rims up front and 22" rims rear

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19181
Re: fiberglass hood
« Reply #6 on: March 06, 2009, 05:22:08 pm »
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10
Pages: [1]   Go Up
« previous next »