« previous next »
Pages: [1] 2   Go Down

Author Topic: vibrashon  (Read 8591 times)

Offline chevy821

  • Newbie
  • Posts: 8
vibrashon
« on: August 29, 2010, 11:21:45 pm »
had my 82 c10 out tonite ran good up till i stoped at a stop singh an i mashed it leaving the stop. Now around 2200 rpms it has a vibraishon idk what it could be any one have an idea
Logged

Offline HAULIN IT

  • Senior Member
  • ****
  • Posts: 1542
Re: vibrashon
« Reply #1 on: August 30, 2010, 02:25:35 am »
I would start looking/prying around at the engine & transmission mounts. Since you didn't mention how/when the vibration occurs,I'd suggest to start there. More details of how/when it vibrates may help someone to better pinpoint your problem. Lorne
Logged

Offline Psycho71

  • Registered Users
  • *
  • Posts: 239
Re: vibrashon
« Reply #2 on: August 30, 2010, 09:53:38 am »
Carrier Bearing maybe? 2pc driveshaft?
Logged
There are two tools needed, duct tape and WD40. If it moves and shouldn't, use the duct tape. If it doesn't move and should, use the WD 40.

Offline Lt.Del

  • Andy aka:SgtDel
  • Senior Member
  • ****
  • Posts: 3864
  • DelbridgePhotography.com
    • www.delbridge.net
Re: vibrashon
« Reply #3 on: August 30, 2010, 05:44:46 pm »
does the vybrashun get worse with higher speeds?  Get her going fast and put the trans in neutral, does the vighbrayshon disappear?  how 'bout when you give her gas while coasting--does it still occur?

A vibraehtion could be the wheel, driveshaft, trans, engine, tire....you need to rule a few things out by a few simple procedures.   
Logged

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19213
Re: vibrashon
« Reply #4 on: August 30, 2010, 07:16:46 pm »
Did you check the U-joints? Maybe that's where the vibrayshun is coming from
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠¯¯¯¯¯'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline chevy821

  • Newbie
  • Posts: 8
Re: vibrashon
« Reply #5 on: September 07, 2010, 02:15:50 am »
yes just form 2500 to 3000 while in drive in N it dosent do it i can feel the tunnel while driving an it feels ruffer more tords the rear of the trans then up by the fire wall

thanks for all the help sofar
Logged

Offline Irish_Alley

  • Tim
  • Senior Member
  • ****
  • Posts: 13333
  • Family is not an important thing. It's everything.
Re: vibrashon
« Reply #6 on: September 07, 2010, 03:54:31 am »
could be a u joint or trans mount craw under the truck and just start trying to move the trans and twist and shake the drive shaft and see what you find
Logged
If you can’t tell yourself the truth, who can you tell it to?~Irish_Alley

When you have eliminated the impossible, whatever remains, however improbable, must be the truth ~Sherlock Holmes

Offline txchainsawgogi

  • Junior Member
  • ***
  • Posts: 584
Re: vibrashon
« Reply #7 on: September 09, 2010, 04:27:44 pm »
Hahaha SgtDel...you left out "vaibreighxun".
Logged

Offline Lt.Del

  • Andy aka:SgtDel
  • Senior Member
  • ****
  • Posts: 3864
  • DelbridgePhotography.com
    • www.delbridge.net
Re: vibrashon
« Reply #8 on: September 09, 2010, 08:03:44 pm »
Quote
Hahaha SgtDel...you left out "vaibreighxun".

lol, i was working tords spelling it that way.
Logged

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19213
Re: vibrashon
« Reply #9 on: September 09, 2010, 10:08:06 pm »
tords? lol
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠¯¯¯¯¯'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline bake74

  • Senior Member
  • ****
  • Posts: 5871
    • Build Thread
Re: vibrashon
« Reply #10 on: September 10, 2010, 01:34:54 am »
          Wow, thought I was the only redneck who didn't know how to spell.  LOL   When you mashed on it, are you getting any wheel hop at all in the rear?  Which when it starts can move through frame to front.  Common on jeeps and lighter 4x4's, just another thought...Tom
Logged
#1: The easiest and most obvious solution to any problem is 99% of the time correct.
#2: There is no such thing as impossible, it just takes longer.
  74 k10, 77k10    Tom

Offline beastie_3

  • Senior Member
  • ****
  • Posts: 3170
  • Josh
    • My truck pics
Re: vibrashon
« Reply #11 on: September 10, 2010, 01:49:53 am »
There arent any rednecks in Cali. They are called hippies...
Logged

Offline bake74

  • Senior Member
  • ****
  • Posts: 5871
    • Build Thread
Re: vibrashon
« Reply #12 on: September 10, 2010, 02:11:05 am »
     For the most part I'd agree with you beastie, but I live up here in the north and would rather call myself a redneck than a bleeding liberal. LOL
Logged
#1: The easiest and most obvious solution to any problem is 99% of the time correct.
#2: There is no such thing as impossible, it just takes longer.
  74 k10, 77k10    Tom

Offline beastie_3

  • Senior Member
  • ****
  • Posts: 3170
  • Josh
    • My truck pics
Re: vibrashon
« Reply #13 on: September 10, 2010, 02:54:16 am »
Ya i know, Im pretty close to santa cruz, berkeley and SF...but your hometown has the worst liberals, politicians!
Logged

Offline Lt.Del

  • Andy aka:SgtDel
  • Senior Member
  • ****
  • Posts: 3864
  • DelbridgePhotography.com
    • www.delbridge.net
Re: vibrashon
« Reply #14 on: September 10, 2010, 11:34:54 am »
What are the odds of Massachusetts and California teaming up and breaking from the union to start the country of CaliChussetts or MassaFornia?  That would be great for the rest of us.
Logged
Pages: [1] 2   Go Up
« previous next »