Author Topic: Tach Conversion Kit Install  (Read 102 times)

Offline 78 K5 Cheyenne

  • Newbie
  • Posts: 5
  • Newbie
Tach Conversion Kit Install
« on: April 15, 2019, 11:02:50 AM »
Hello all,

I am very new, both to this community, and to these trucks. So, please bare with me as I try to explain my issue.

I picked up a tachometer conversion kit from... a vendor. If you aren't familiar with this, it replaces the big gas gauge to the right of the speed-o with a tachometer, and moves the fuel gauge to the small spot to the bottom left spot, where I believe there would have either been a warning light, or a clock (mine was equipped with a clock). It's all pretty straight forward, and the kit is nice because it comes with the two gauges, tach wiring harness, a new cluster 'chassis', new lens, new backing plate/spacer, circuit and clips. Everything one would need.

Since I'm such a newb, I haven't really ever done any sort of wiring under a dash or for instruments in a cluster like this, but this tachometer wiring seemed pretty easy, as it is really only three wires. Power (ignition-ed 12V), signal (harness came with the correct clip which plugs into the 'Tach' terminal on the HEI Distributor) and ground (self-explanatory).

I got everything taken apart, got all new bulbs, dielectric grease, put everything back together, wired everything up, tested that I had a good 12V ignition-ed source, good clean ground, ran the signal clip through the fire wall, to the HEI, ,clipped it in there, went to turn the ignition to 'Run' position, and... nothing. The needle on the tach didn't even move to zero when I turned on the ignition. Just stayed floating at like 1,100 rpm, where it had been the whole time.

I took my handy-dandy multi-meter, checked to make sure it is getting the required 12V at the clip on the back of the tach, and it is. I guess I'm not sure what else could be the issue, unless it's just a faulty tach that was DOA? Is it possible that I am not getting a signal from that tach terminal on the distributor? I would imagine it is getting signal, if the truck starts, but who knows. As I said, I'm no expert.

Any thoughts, suggestions, ideas would be most helpful.

-Mike
Mike - 1978 K-5

Offline rayjos_1

  • Newbie
  • Posts: 7
  • Newbie
Re: Tach Conversion Kit Install
« Reply #1 on: April 15, 2019, 11:15:33 AM »
I know that when I installed an Edelbrock E-street TBI, I had to install an MSD unit for the tach to hook up to the ECU on my 1976 Silverado. I hear the Tach connection on the HEI sucks and does not give a good signal.

Offline JohnnyPopper

  • Registered Users
  • *
  • Posts: 193
  • Newbie
Re: Tach Conversion Kit Install
« Reply #2 on: April 16, 2019, 01:37:03 PM »
Sounds like DOA, the needle should 0 out when 12v is applied. Does your gas gauge work? 

Offline 78 K5 Cheyenne

  • Newbie
  • Posts: 5
  • Newbie
Re: Tach Conversion Kit Install
« Reply #3 on: April 17, 2019, 01:02:54 PM »
Sounds like DOA, the needle should 0 out when 12v is applied. Does your gas gauge work?

I actually don't think it is... it is maxed to full. It was pretty full when I did the conversion, but it seems to be pegged past full atm... I drove it a few miles yesterday, and it didn't move at all.

Beginning to think it isn't working either.

I did get confirmation from the vendor that they are willing to send me another tach, so that's good. I'll see what happens when it arrives.
Mike - 1978 K-5

Offline bd

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 5112
Re: Tach Conversion Kit Install
« Reply #4 on: April 17, 2019, 02:05:47 PM »
Regarding the tach:  verify I+, ground and tach signal from the distributor using your meter or test light.  If all three circuits function properly, the tach head is faulty.

Regarding the fuel Gauge:  repair the open circuit between the gauge and the fuel tank sending unit.
Rich
It's difficult to know just how much you don't know, until you know it....
In other words... if people learn by making mistakes, by now I should know just about everything!!
87 R10 Silverado Fleetside 355 MPFI 700R4 3.42 Locker (aka Rusty, aka Mater)