« previous next »
Pages: 1 ... 25 26 [27] 28 29 ... 33   Go Down

Author Topic: 83 c10 re-innovated Pro Touring  (Read 413388 times)

Offline bake74

  • Senior Member
  • ****
  • Posts: 5871
    • Build Thread
Re: 83 c10 re-innovated, air ride
« Reply #390 on: April 12, 2014, 07:29:33 am »
Quote from: tex62 on April 12, 2014, 06:59:41 am
So I noticed you welded in the cross member over the motor. So what happens if the motor goes and you need to pull it? Guess it isn't a big deal to cut and weld it back in place though when the time comes.

      It is not the easiest to see but the cross bar (over engine) I believe comes out, look closer at these 2 pics.

Logged
#1: The easiest and most obvious solution to any problem is 99% of the time correct.
#2: There is no such thing as impossible, it just takes longer.
  74 k10, 77k10    Tom

Offline tex62

  • Newbie
  • Posts: 31
  • Lurker
Re: 83 c10 re-innovated, air ride
« Reply #391 on: April 12, 2014, 08:01:33 am »
Quote from: bake74 on April 12, 2014, 07:29:33 am
Quote from: tex62 on April 12, 2014, 06:59:41 am
So I noticed you welded in the cross member over the motor. So what happens if the motor goes and you need to pull it? Guess it isn't a big deal to cut and weld it back in place though when the time comes.

      It is not the easiest to see but the cross bar (over engine) I believe comes out, look closer at these 2 pics.



Yes sir I missed it completely. Good eye!
Logged
87 chevy suburban. 350 tbi w/ 700r4. 2wd sluggish tank sporting plastidip paint.

Offline the dan

  • Frequent Member
  • **
  • Posts: 321
Re: 83 c10 re-innovated, air ride
« Reply #392 on: July 12, 2014, 12:58:32 am »
So rust bullet sucks, more so the etch meathod i believe, paint didnt adhere to the metal



cleaned the heads up, matched, valve seals, and a little casting clean, along with new springs


ARP'd out the 6.0l



milled the lifter valley cover flat so it didnt look so crappy


cleaned and painted the oil pan, glass bead the motor mounts


Shortened up the dip stick




made my throwout bearing -3an and extended the bleeder


as she sits




other than the paint lifting i did all of that yesterday/last night. i used my strike of motivation

Logged
83 C10 Pro-touring, Forged 408 Stroker LS, Paxton supercharger, T56 magnum, Detroit 9", and horrible paint

Offline the dan

  • Frequent Member
  • **
  • Posts: 321
Re: 83 c10 re-innovated, air ride
« Reply #393 on: July 12, 2014, 01:01:13 am »
Quote from: 87V20Kansan on February 27, 2014, 08:04:52 pm
This truck is so cool.
Quote from: tex62 on April 12, 2014, 06:59:41 am
So I noticed you welded in the cross member over the motor. So what happens if the motor goes and you need to pull it? Guess it isn't a big deal to cut and weld it back in place though when the time comes.
sorry i havent been at a computer lately, generally dealing with iphones for interenet.

yes its removable as stated. its kinda hidden, pretty fun part to make
Logged
83 C10 Pro-touring, Forged 408 Stroker LS, Paxton supercharger, T56 magnum, Detroit 9", and horrible paint

Offline bake74

  • Senior Member
  • ****
  • Posts: 5871
    • Build Thread
Re: 83 c10 re-innovated, air ride
« Reply #394 on: July 12, 2014, 09:31:44 am »
     At least you got some time to work on your truck.
     My honey do list just keeps getting bigger.  Gotta say though, wife is gone all next week for work, wife gone = any extra time I get not at work will be on truck.
Logged
#1: The easiest and most obvious solution to any problem is 99% of the time correct.
#2: There is no such thing as impossible, it just takes longer.
  74 k10, 77k10    Tom

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19167
Re: 83 c10 re-innovated, air ride
« Reply #395 on: July 15, 2014, 05:30:59 pm »
Awesome!
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline the dan

  • Frequent Member
  • **
  • Posts: 321
Re: 83 c10 re-innovated, air ride
« Reply #396 on: August 07, 2014, 12:41:34 am »

Polished the tank


got some work done tonight let me tell you...




tucked the wires

Logged
83 C10 Pro-touring, Forged 408 Stroker LS, Paxton supercharger, T56 magnum, Detroit 9", and horrible paint

Offline bake74

  • Senior Member
  • ****
  • Posts: 5871
    • Build Thread
Re: 83 c10 re-innovated, air ride
« Reply #397 on: August 08, 2014, 07:23:24 pm »
     Those spark plug wires will be fun to change.
Logged
#1: The easiest and most obvious solution to any problem is 99% of the time correct.
#2: There is no such thing as impossible, it just takes longer.
  74 k10, 77k10    Tom

Offline the dan

  • Frequent Member
  • **
  • Posts: 321
Re: 83 c10 re-innovated, air ride
« Reply #398 on: August 13, 2014, 11:12:51 am »
Not at all. Finishing making them is going to be the hard part
Logged
83 C10 Pro-touring, Forged 408 Stroker LS, Paxton supercharger, T56 magnum, Detroit 9", and horrible paint

Offline the dan

  • Frequent Member
  • **
  • Posts: 321
Re: 83 c10 re-innovated, air ride
« Reply #399 on: September 03, 2014, 06:51:02 pm »







 finished assembling my accessories, also made my steam port cross over for the heads and fit it to the waterpump
Logged
83 C10 Pro-touring, Forged 408 Stroker LS, Paxton supercharger, T56 magnum, Detroit 9", and horrible paint

Offline FlatBlack77

  • Junior Member
  • ***
  • Posts: 894
  • Cheap Fast Reliable - Pick 2
Re: 83 c10 re-innovated, air ride
« Reply #400 on: September 03, 2014, 10:31:14 pm »
MOAR
Logged
"When you are a hammer, everything looks like a nail"
'77 C/10 - 350/350 mild street motor

Offline the dan

  • Frequent Member
  • **
  • Posts: 321
Re: 83 c10 re-innovated, air ride
« Reply #401 on: September 15, 2014, 08:44:46 pm »
Quote from: FlatBlack77 on September 03, 2014, 10:31:14 pm
MOAR

Your wish is my demand (?)

Finished up my fuel rails and injectors, wired them up and hid the wires


Finished my power steering feed line


And then since my tensioner isn't going to work, I purchased a new one


Paxton Novi 2000, a little bigger than I wanted but the price was right, should be pulling it off his corvette in a week or two
Logged
83 C10 Pro-touring, Forged 408 Stroker LS, Paxton supercharger, T56 magnum, Detroit 9", and horrible paint

Offline bake74

  • Senior Member
  • ****
  • Posts: 5871
    • Build Thread
Re: 83 c10 re-innovated, air ride
« Reply #402 on: September 16, 2014, 08:42:48 am »
     Actually after seeing put together, it makes more sense now.  That truck is going to be a work of art when you are done.
Logged
#1: The easiest and most obvious solution to any problem is 99% of the time correct.
#2: There is no such thing as impossible, it just takes longer.
  74 k10, 77k10    Tom

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19167
Re: 83 c10 re-innovated, air ride
« Reply #403 on: September 16, 2014, 07:38:05 pm »
It already is!
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline frotosride

  • Senior Member
  • ****
  • Posts: 1428
    • WFO CONCEPTS
Re: 83 c10 re-innovated, air ride
« Reply #404 on: September 16, 2014, 09:38:06 pm »
Quote from: VileZambonie on September 16, 2014, 07:38:05 pm
It already is!
Biggest understatement I've seen yet!! how in the world are you able to d all this and afford to school at the same time?.. Keep it coming!
Logged
"Beat it like a red-headed ford"
1987 v10 Silverado(LQ4), 87 R10,83 K20, 83 cucv 6.2 Detroit
2006 Boulevard M109R 109 cid,2019 M109R BOSS
2009 Jeep XK, (future LS Swap)
GSXR 750 engine awaiting go kart
Pages: 1 ... 25 26 [27] 28 29 ... 33   Go Up
« previous next »