« previous next »
Pages: [1]   Go Down

Author Topic: rockers  (Read 6273 times)

Offline mikewb

  • Registered Users
  • *
  • Posts: 167
rockers
« on: March 02, 2008, 07:00:42 pm »
how tight should rocker arms be? should i be able to move them?
Logged

Offline 86 chevy silverado

  • Registered Users
  • *
  • Posts: 212
Re: rockers
« Reply #1 on: March 02, 2008, 07:39:25 pm »
When rockers are properly adjusted (I preach 0 valve lash) the rocker will wiggle around but should not have any up and down movement, if that answers your question. Do not re-use your intake gaskets unless they were just replaced recently, old gaskets should never be reused-to answer your other question on your other thread. Its easier to ask both questions on one thread.
Logged

Offline Robry 87

  • Newbie
  • Posts: 44
Re: rockers
« Reply #2 on: March 02, 2008, 10:35:26 pm »
I just built my motor and i had a heck of a time getting my just right but i can help if your stock or useing hidralik work with me i can't speel the best.
do you have a book  on your motor or truck your going to need it.to know the rotion of valve seting,and my rokers still move some but not up,and down.you will won't the push rod to just turn with your fingers not loose just wear you can't turn it will make it run then will go from there.
Logged

Offline Robry 87

  • Newbie
  • Posts: 44
Re: rockers
« Reply #3 on: March 02, 2008, 11:18:38 pm »
Check mesg i can help you with this be on tomarow night.
Logged

Offline Captkaos

  • OWNER and Administrator
  • Administrator
  • Senior Member
  • *****
  • Posts: 18460
    • http://www.73-87chevytrucks.com
Re: rockers
« Reply #4 on: March 03, 2008, 09:59:50 am »
They are going to be a little loose if the motor has been sitting since there is no pressure in the lifters.  What are we working on?  And what is it status?  Just rebuilt, been sitting for years, etc...
Logged

Offline joesgarage71

  • Wrench
  • Senior Member
  • ****
  • Posts: 1156
Re: rockers
« Reply #5 on: March 09, 2008, 02:23:37 pm »
 They will move some side to side but not up and down(very little pressure). If the lifter is on base of the cam you can move the rocker up and down(movement from the plunger inside of the lifter, cold engine)
 New parts 3/4-1 turn after zero lash, used parts 1/2 to 1/4 turn adjustment.
Logged
78' K-20 355/SM465/twin stick 205 6" on 36's
14 bolt FF/big bearing Dana 44 4.56 gears
92' GMC C-1500 454/4L80E/14 bolt

Offline 86 chevy silverado

  • Registered Users
  • *
  • Posts: 212
Re: rockers
« Reply #6 on: March 09, 2008, 06:07:46 pm »
A manual will state 3/4 turn past 0 valve lash with stock parts. With performance lifters 0 to 1/4 past 0 lash is recommended, I should be more specific. That is coming from a guy that has built race motors for 20+ years, one of my mentors in the past.
Logged

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19177
Re: rockers
« Reply #7 on: March 22, 2008, 08:06:09 pm »
Quote from: 76 k10 on March 22, 2008, 08:03:07 pm
Quote from: mikewb on March 02, 2008, 07:00:42 pm
how tight should rocker arms be? should i be able to move them?
ya man man you some locktight on ummm yeeeeeeeeehaaaaaa

Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline mikewb

  • Registered Users
  • *
  • Posts: 167
rocker
« Reply #8 on: March 24, 2008, 04:33:19 pm »
what tool to do you use to set rockers?
Logged

Offline Captkaos

  • OWNER and Administrator
  • Administrator
  • Senior Member
  • *****
  • Posts: 18460
    • http://www.73-87chevytrucks.com
Re: rocker
« Reply #9 on: March 24, 2008, 04:55:12 pm »
Are you talking about setting the lash?
Logged

Offline mikewb

  • Registered Users
  • *
  • Posts: 167
Re: rocker
« Reply #10 on: March 24, 2008, 05:38:30 pm »
Yeah
Logged

Offline Captkaos

  • OWNER and Administrator
  • Administrator
  • Senior Member
  • *****
  • Posts: 18460
    • http://www.73-87chevytrucks.com
Re: rocker
« Reply #11 on: March 25, 2008, 03:22:25 pm »
Hydraulic or solid?
I am going to assume hydraulic and say you need a 5/8" wrench to get the lash out and then tighten another 1/2 turn.

Check this link:   http://www.73-87.com/7387garage/drivetrain/valvlash.htm
Logged
Pages: [1]   Go Up
« previous next »