« previous next »
Pages: [1]   Go Down

Author Topic: Input shaft spect sm 465  (Read 5505 times)

Offline BULLDOG

  • Newbie
  • Posts: 49
Input shaft spect sm 465
« on: May 21, 2010, 08:11:01 am »
Does anyone know the input shaft size and spine count for sm 465
Logged
Black 1983 K20 and sm 465

Offline Irish_Alley

  • Tim
  • Senior Member
  • ****
  • Posts: 13333
  • Family is not an important thing. It's everything.
Re: Input shaft spect sm 465
« Reply #1 on: May 21, 2010, 02:44:41 pm »
What shaft. You talking about were you put the alignment tool in?
Logged
If you can’t tell yourself the truth, who can you tell it to?~Irish_Alley

When you have eliminated the impossible, whatever remains, however improbable, must be the truth ~Sherlock Holmes

Offline BULLDOG

  • Newbie
  • Posts: 49
Re: Input shaft spect sm 465
« Reply #2 on: May 21, 2010, 06:47:59 pm »
I have a friend that has a Center force pressure plate and DF clutch with low milage I need to know if the clutch spline count and shaft size will work with the center force clutch?
I am pretty sure that the clutch is 26 spline with a 1 1/8 inch shaft

Logged
Black 1983 K20 and sm 465

Offline Irish_Alley

  • Tim
  • Senior Member
  • ****
  • Posts: 13333
  • Family is not an important thing. It's everything.
Re: Input shaft spect sm 465
« Reply #3 on: May 21, 2010, 07:06:13 pm »
What's his plate for?
Logged
If you can’t tell yourself the truth, who can you tell it to?~Irish_Alley

When you have eliminated the impossible, whatever remains, however improbable, must be the truth ~Sherlock Holmes

Offline joesgarage71

  • Wrench
  • Senior Member
  • ****
  • Posts: 1156
Re: Input shaft spect sm 465
« Reply #4 on: May 21, 2010, 09:06:10 pm »
10 spline
Logged
78' K-20 355/SM465/twin stick 205 6" on 36's
14 bolt FF/big bearing Dana 44 4.56 gears
92' GMC C-1500 454/4L80E/14 bolt

Offline Irish_Alley

  • Tim
  • Senior Member
  • ****
  • Posts: 13333
  • Family is not an important thing. It's everything.
Re: Input shaft spect sm 465
« Reply #5 on: May 22, 2010, 01:12:33 am »
10 splines yes but more than likely its a 1-1/8" shaft but it might be a 1-1/2" shaft
Logged
If you can’t tell yourself the truth, who can you tell it to?~Irish_Alley

When you have eliminated the impossible, whatever remains, however improbable, must be the truth ~Sherlock Holmes

Offline jaredts

  • Senior Member
  • ****
  • Posts: 1330
Re: Input shaft spect sm 465
« Reply #6 on: June 03, 2010, 06:35:00 am »
1-1/8" diameter 10 spline.  Did an internet search for "sm465 input shaft" and grabbed the first website that came up: http://www.novak-adapt.com/knowledge/sm465.htm.
Logged

Offline Irish_Alley

  • Tim
  • Senior Member
  • ****
  • Posts: 13333
  • Family is not an important thing. It's everything.
Re: Input shaft spect sm 465
« Reply #7 on: June 03, 2010, 11:09:43 pm »
Yes but there are two dif size shafts
Logged
If you can’t tell yourself the truth, who can you tell it to?~Irish_Alley

When you have eliminated the impossible, whatever remains, however improbable, must be the truth ~Sherlock Holmes

Offline jaredts

  • Senior Member
  • ****
  • Posts: 1330
Re: Input shaft spect sm 465
« Reply #8 on: June 04, 2010, 05:35:14 am »
That website looked legit. and states only one input shaft size.  A few different output shafts.
Logged

Offline Grim 82

  • Senior Member
  • ****
  • Posts: 1651
Re: Input shaft spect sm 465
« Reply #9 on: June 04, 2010, 09:39:46 am »
http://www.4wheeloffroad.com/brandpages/chevy/131_0208_sm465_transmission_rebuild/index.html

Irish is right. Bulldog, if its for a 465 it will be 10 spline, but it will be 1 of 2 shaft diameters. Do you know what vehicle application the centerforce was used on?
Logged
Give a man a gun, and he might rob a bank. Give a man a bank, and he might rob the world.
Pages: [1]   Go Up
« previous next »