« previous next »
Pages: [1]   Go Down

Author Topic: thread size  (Read 3638 times)

Offline Bitzer!

  • Junior Member
  • ***
  • Posts: 906
  • Smiles per gallon
thread size
« on: January 25, 2012, 02:53:28 pm »
Hi guys, I've popped up here now!

Starter problem sorted, exh headers fitted and pipes mocked up in position, a few tweaks needed but good enough for now.

I was to dispose of the ugly viscous fan and I'll run a 'lecky one (as Viles but prob not as pretty!)

Here's where I've got to: Fan etc off, studs removed from water pump drive. The question now is what size thread do I need to bolt the pulley back on?

It tends to be specialist places over here that deal with imperial now, the "normal" routes only deal in metric! It's easy to ask direct for what I need rather than explain to a do-nut that hasn't a clue.

Any one shed any light?

cheers

Andy
Logged
1979 GMC CrewCab  C20 1t
454 750 Holley,TH350, 14bolt diff fully floating
Why aren't there 8 days in a week!
A K5 rolling shell *new addition*

Offline thirsty

  • Senior Member
  • ****
  • Posts: 1289
    • Suitor's Garage
Re: thread size
« Reply #1 on: January 25, 2012, 03:38:48 pm »
5/16x24 NF by however long you need them Andy.
Don't forget to get some new lock washers with them too so they don't loosen up on you.
Logged
Real trucks are built, not bought Build thread

Give me a long enough lever and a place to stand, and I shall move the earth or break this bolt...Whatever, just hold my beer!

Offline Bitzer!

  • Junior Member
  • ***
  • Posts: 906
  • Smiles per gallon
Re: thread size
« Reply #2 on: January 25, 2012, 03:45:18 pm »

Cheers me old china!

Sorry - translation > Why thank you for your help young man

 ;D
Logged
1979 GMC CrewCab  C20 1t
454 750 Holley,TH350, 14bolt diff fully floating
Why aren't there 8 days in a week!
A K5 rolling shell *new addition*

Offline thirsty

  • Senior Member
  • ****
  • Posts: 1289
    • Suitor's Garage
Re: thread size
« Reply #3 on: January 25, 2012, 07:50:25 pm »
Before you take my word for it Bitzer, I just remembered that you have a big block and the water pump I checked was on a small block. I'm not 100% sure they are the same thread size.
Hopefully someone else that has a big block can check. Sorry if I gave you wrong info.
Logged
Real trucks are built, not bought Build thread

Give me a long enough lever and a place to stand, and I shall move the earth or break this bolt...Whatever, just hold my beer!

Offline zieg85

  • Global Moderator
  • Senior Member
  • ****
  • Posts: 7595
    • 73-87 GM squarebody extended cab and conversions up to 91 R/V series
Re: thread size
« Reply #4 on: January 25, 2012, 08:41:07 pm »
yep it is the same
Logged
Carl 
1985 C20 Scottsdale 7.4L 4 speed 3.21
1986 C10 under construction
https://www.facebook.com/groups/248658382003506/

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19182
Re: thread size
« Reply #5 on: January 25, 2012, 09:18:11 pm »
use flat washers and loctite instead.
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline jaredts

  • Senior Member
  • ****
  • Posts: 1330
Re: thread size
« Reply #6 on: January 25, 2012, 10:12:59 pm »
Do some research on lockwashers.  They are only effective in a few circumstances where only a very small torque can be applied.  They are otherwise counterproductive.  Cryin' shame that so many engineers still spec. these out for anything but plastic or thin sheet metal.
Logged

Offline Bitzer!

  • Junior Member
  • ***
  • Posts: 906
  • Smiles per gallon
Re: thread size
« Reply #7 on: January 26, 2012, 06:22:48 am »

As always, cheers all.

Parts ordered and will be here 2mow.

That's another bit done!!
Logged
1979 GMC CrewCab  C20 1t
454 750 Holley,TH350, 14bolt diff fully floating
Why aren't there 8 days in a week!
A K5 rolling shell *new addition*
Pages: [1]   Go Up
« previous next »