« previous next »
Pages: [1]   Go Down

Author Topic: Ford Problems  (Read 5433 times)

Offline 1979C20

  • Senior Member
  • ****
  • Posts: 1659
  • Kyle Taulton.
Ford Problems
« on: April 18, 2014, 11:06:18 am »
Not sure where to turn here for answers so I figured I would ask around here. My buddy has a '90 ish ranger thats prerunned and has a 4.0v6 out of a 2001 explorer sport trac in it. He bought the truck the way it is. One night we were offroading and while cruising down the wash his truck died. He found the computer touching the starter solenoid. He replaced the computer and prom chip, as well as the frame mounted inline fuel pump with aftermarket wiring and relay. We cannot get the truck to run to save our lives. Hes got about 50psi at the rail, good strong spark, and good fuel. It will run on carb spray for a bit, but will not run on its own. One thing I noticed when I tested voltage at one of the Injectors was that both wires in the harness have 12v with ignition on. Im not sure if thats normal or not. Any ideas on what to test? All fuses are good and there are no engine codes.
Logged
1979 SCLB C20 Q-jet 350 SM465 14b F.F. 4.10 G80
1989 GMC Suburban V2500 TBI350 TH400 4in lift 35's 14b SF

Offline LeftysRodandCustom

  • Newbie
  • Posts: 72
  • Newbie
Re: Ford Problems
« Reply #1 on: April 18, 2014, 01:02:06 pm »
Some older fuel injected fords have a rollover switch that shuts them down in the event of a rollover. Had a buddy find this out the hard way with a country squire station wagon, it does have a reset on it and that fixed the problem. It didnt take a rollover to set it off, but some dukes of hazad type stuff was enough. Mainly though i suspect you'll find the real issue highlighted in blue and circled on the grill.
Logged

Offline bake74

  • Senior Member
  • ****
  • Posts: 5871
    • Build Thread
Re: Ford Problems
« Reply #2 on: April 18, 2014, 09:11:28 pm »
     Here is a step by step tutorial on testing a no-start ford 4.0.
     This should give you some points to check and hopefully be "the man" to your buddy.   8)
« Last Edit: April 19, 2014, 09:35:39 am by bake74 »
Logged
#1: The easiest and most obvious solution to any problem is 99% of the time correct.
#2: There is no such thing as impossible, it just takes longer.
  74 k10, 77k10    Tom

Offline Irish_Alley

  • Tim
  • Senior Member
  • ****
  • Posts: 13333
  • Family is not an important thing. It's everything.
Re: Ford Problems
« Reply #3 on: April 18, 2014, 11:11:24 pm »
my moms e150 had a no start issue it turns out to be the crankshaft position sensor. cleaned up the terminals and it started up no problem. had good fuel pressure spark and injector signal.
Logged
If you can’t tell yourself the truth, who can you tell it to?~Irish_Alley

When you have eliminated the impossible, whatever remains, however improbable, must be the truth ~Sherlock Holmes

Offline Engineer

  • Senior Member
  • ****
  • Posts: 1402
Re: Ford Problems
« Reply #4 on: April 20, 2014, 07:44:12 am »
Ford Problems?

Is there enough bandwidth on this site to list them all..........
Logged
2002 Chevy 2500HD 4x4 8.1/ZF6sp RC/LB
2001 Chevy 2500HD 4x4 6.0/4L85E EC/SB
1997 Chevy Blazer 4x4
1994 Chevy K-2500 4x4 C6P 5.7/4L80E
1979 Chevy K-30 4x4 4sp 4.10
1977 Chevy K-30 4x4 4sp 4.10 454

Dad of an Eagle Scout, and a Life Scout

Offline 87V20Kansan

  • Newbie
  • Posts: 79
Re: Ford Problems
« Reply #5 on: April 20, 2014, 12:57:35 pm »
Quote from: Engineer on April 20, 2014, 07:44:12 am
Ford Problems?

Is there enough bandwidth on this site to list them all..........

There isn't enough bandwidth on this site to deal with the problems ONLY associated with the 6.0 powerstroke.
Logged
Cecil: 1987 V20, TBI 350, TH400, 4:10's, 7" lift, 37" H1 beadlocked runflats. Cummins swap someday.

Offline 1979C20

  • Senior Member
  • ****
  • Posts: 1659
  • Kyle Taulton.
Re: Ford Problems
« Reply #6 on: April 20, 2014, 05:21:55 pm »
That tutorial didnt help.
Logged
1979 SCLB C20 Q-jet 350 SM465 14b F.F. 4.10 G80
1989 GMC Suburban V2500 TBI350 TH400 4in lift 35's 14b SF

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19177
Re: Ford Problems
« Reply #7 on: April 20, 2014, 05:54:03 pm »
Do you have a scan tool? You need to look at some PID's
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠¯¯¯¯¯'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline 1979C20

  • Senior Member
  • ****
  • Posts: 1659
  • Kyle Taulton.
Re: Ford Problems
« Reply #8 on: April 22, 2014, 12:20:09 am »
Will a scan tool actually show me information I need when the vehicle wont start/run? I dont own a scan tool, but I may have access to one
Logged
1979 SCLB C20 Q-jet 350 SM465 14b F.F. 4.10 G80
1989 GMC Suburban V2500 TBI350 TH400 4in lift 35's 14b SF

Offline 79K10Crusher

  • Newbie
  • Posts: 31
Re: Ford Problems
« Reply #9 on: May 05, 2014, 05:22:18 pm »
The ranger I use to drive in high school had a switch in the passenger side floorboard right at the top of the carpet. Tall long legged people would always hit it and knock it loose. Might want to check that.
Logged
Pages: [1]   Go Up
« previous next »