« previous next »
Pages: [1]   Go Down

Author Topic: 350 Timing Question  (Read 5121 times)

Offline 327power

  • Registered Users
  • *
  • Posts: 164
350 Timing Question
« on: August 02, 2010, 10:47:18 pm »
Hi!, It's been a while but I got my new Goodwrench 350 running finally, but when I hook up the timing light to the #1 piston, no marks show up! If I hook it up to #8 piston, then I see the timing mark on the balancer. Now we know that #8 is the second to fire after #1. What is going on?
Also, the engine is shaky at idle even though I've tuned the Holley 600 the best I can. Any assistance would be awesome. Thanks!
Logged
LIVE FREE OR DIE

Offline frotosride

  • Senior Member
  • ****
  • Posts: 1428
    • WFO CONCEPTS
Re: 350 Timing Question
« Reply #1 on: August 02, 2010, 11:11:21 pm »
I know it sucks to hear this but it sounds like #1 isn't firing. The shaking is prob #1 not pulling it's weight. Check the wires plug and pull the plug out to see if it's firing.
Logged
"Beat it like a red-headed ford"
1987 v10 Silverado(LQ4), 87 R10,83 K20, 83 cucv 6.2 Detroit
2006 Boulevard M109R 109 cid,2019 M109R BOSS
2009 Jeep XK, (future LS Swap)
GSXR 750 engine awaiting go kart

Offline cruisinc10

  • Newbie
  • Posts: 41
Re: 350 Timing Question
« Reply #2 on: August 03, 2010, 09:48:30 am »
sounds like a problem w/ the distibutor
Logged
1986 C10 355Ci/TH350/2 inch drop/275/60/15 cooper cobra Tires/flat black w/pinstriping- sold

1984 K10 Silverado 305Ci/Th350/6 inch all spring lift/33/12.5/15 interco Trxus MT Tires/factory red and white-Daily Driver

Offline Grim 82

  • Senior Member
  • ****
  • Posts: 1651
Re: 350 Timing Question
« Reply #3 on: August 03, 2010, 10:23:51 am »
You can use your timing light to check for spark in the wires up to the plugs. Clip it on each wire and make sure it strobes. Remove and check all of the plugs. If the plugs are all good and the timing light strobes on all 8 wires, go and re-check TDC. Verify that the dist is in right. Find TDC #1 cylinder and make sure the rotor is pointed at it, and confirm it with the mark on the balancer. Then check and triple check your firing order with the wires.
Logged
Give a man a gun, and he might rob a bank. Give a man a bank, and he might rob the world.

Offline 327power

  • Registered Users
  • *
  • Posts: 164
Re: 350 Timing Question
« Reply #4 on: August 03, 2010, 02:23:04 pm »
The distributor seems to be in right. How could you put it in wrong and have it running? It is a jegs distributor.
Logged
LIVE FREE OR DIE

Offline Grim 82

  • Senior Member
  • ****
  • Posts: 1651
Re: 350 Timing Question
« Reply #5 on: August 03, 2010, 02:46:30 pm »
Check and recheck the wire location (firing order). Make sure you don't have any wires switched. I don't know if it would run if it was 180 off, but you can pull #1 plug and make sure its TDC on the compression stroke, not the exhaust stroke. It could be a tooth off. There's 8 cylinders but 12 teeth on the gear.
Logged
Give a man a gun, and he might rob a bank. Give a man a bank, and he might rob the world.

Offline bake74

  • Senior Member
  • ****
  • Posts: 5871
    • Build Thread
Re: 350 Timing Question
« Reply #6 on: August 04, 2010, 06:20:55 pm »
  Let's just hope the camshaft and crank got lined up right when the motor was put together.
Logged
#1: The easiest and most obvious solution to any problem is 99% of the time correct.
#2: There is no such thing as impossible, it just takes longer.
  74 k10, 77k10    Tom

Offline Lt.Del

  • Andy aka:SgtDel
  • Senior Member
  • ****
  • Posts: 3864
  • DelbridgePhotography.com
    • www.delbridge.net
Re: 350 Timing Question
« Reply #7 on: August 04, 2010, 06:29:50 pm »
Quote
Let's just hope the camshaft and crank got lined up right when the motor was put together.

I was thinking that myself, Bake, but, i figured, seeing that it is a Goodwrench engine, i'd think the techs putting it together could line up the two dots, but, as with anything touched by humans, mistakes can happen.
Logged
Pages: [1]   Go Up
« previous next »