« previous next »
Pages: [1]   Go Down

Author Topic: Carb?  (Read 6360 times)

Offline 86Chevy3

  • Newbie
  • Posts: 12
Carb?
« on: January 12, 2011, 07:29:32 pm »
I built a 383 recently and it seems like it needs to be timed or the carb needs to be adjusted, I timed it and it's still acting up so I'm thinkin it's the carb, I've tried adjusting it but I was wondering if I needed to change out the squirter nozzle or the power valve, it's flooding out but also backfiring, I've got it to where it idles pretty descent but it seems sluggish during low rpms and clears up higher in the rev range so I dint really know what I need to do, I'm thinkin about paying a guy I know to tune it up for me hopefully that's all it needs
Logged

Offline ToddN

  • Newbie
  • Posts: 93
Re: Carb?
« Reply #1 on: January 12, 2011, 09:01:02 pm »
Vac. leak?
Logged
A government big enough to give you everything you need, is a government big enough to take everything you have.

Offline MITOYZ

  • Newbie
  • Posts: 15
Re: Carb?
« Reply #2 on: January 21, 2011, 06:54:01 pm »
sounds like a blown power valve, but dont know if its a Holley or not
Logged

Offline TexasRed

  • Junior Member
  • ***
  • Posts: 727
Re: Carb?
« Reply #3 on: January 21, 2011, 08:23:38 pm »
Stock carb, stock distributor? You have the vac. advance going to ported or manifold?
Logged

Offline 86Chevy3

  • Newbie
  • Posts: 12
Re: Carb?
« Reply #4 on: January 22, 2011, 05:29:55 pm »
its a holly street avenger 670, proform hei distributor, and vacuum advance is hooked up to vacuum port on the carb
Logged

Offline Irish_Alley

  • Tim
  • Senior Member
  • ****
  • Posts: 13333
  • Family is not an important thing. It's everything.
Re: Carb?
« Reply #5 on: January 22, 2011, 05:40:13 pm »
Retard it a inch and go from there. I put my 670 at 8 degrees and something you saying retarded it and gave it that take off power you lacking not sure what it timed to now but much better
Logged
If you can’t tell yourself the truth, who can you tell it to?~Irish_Alley

When you have eliminated the impossible, whatever remains, however improbable, must be the truth ~Sherlock Holmes

Offline 1980c10

  • Senior Member
  • ****
  • Posts: 1205
Re: Carb?
« Reply #6 on: January 22, 2011, 11:59:18 pm »
I have heard of an issue with proform distributors that allows the dist to turn on the shaft. so try to turn the dist by hand while watching the base if it moves without the base moving(by the hold down clamp) that would defintley be your problem.
Logged

Offline bake74

  • Senior Member
  • ****
  • Posts: 5871
    • Build Thread
Re: Carb?
« Reply #7 on: January 24, 2011, 08:06:57 am »
     One more option, I had a problem before like you said, at lower rpm it would backfire but at higher rpm it leveled out and ran fine, my headers were loose and after tightening them it ran better at lower rpm's..
Logged
#1: The easiest and most obvious solution to any problem is 99% of the time correct.
#2: There is no such thing as impossible, it just takes longer.
  74 k10, 77k10    Tom

Offline Grim 82

  • Senior Member
  • ****
  • Posts: 1651
Re: Carb?
« Reply #8 on: January 24, 2011, 09:59:07 am »
Quote from: 86Chevy3 on January 12, 2011, 07:29:32 pm
I built a 383 recently and it seems like it needs to be timed or the carb needs to be adjusted

Verify TDCC and make sure you have your firing order right. Set your idle mixture with a vacuum gauge if you have one. Was that a new carb, or one that was working fine before the 383 build?
Logged
Give a man a gun, and he might rob a bank. Give a man a bank, and he might rob the world.

Offline bowtieman82

  • Newbie
  • Posts: 58
Re: Carb?
« Reply #9 on: February 09, 2011, 04:08:13 pm »
i know alot about holley cards. what jet size do u have now and size did it come with when was new. what is your elevation. what type of cam do u have how much comperion do u have. i have a 350 with a road deman, with a voo doo cam and a MSD HEI it make 400HP and it get 16 MPG in a 82 chevy 4x4 with 33's. soit u need help ask me.
Logged
Pages: [1]   Go Up
« previous next »