« previous next »
Pages: [1] 2   Go Down

Author Topic: Shaking problem  (Read 8440 times)

Offline Slammed83

  • Newbie
  • Posts: 18
Shaking problem
« on: January 15, 2011, 11:06:11 pm »
Hey guys i cant figure out whats wrong with my truck. It idles normal then when i shift it it kicks hard, But thats because the idle is high because of the electric choke. If im going down the road and go over 1200 rpm the truck gets a death shake. I did a burnout last friday then it started acting up. I tried one today also. Last week the passenger side spun and driver didnt. Today it was the other way around. So im wondering if i didnt mess up something in my rear end. What's your guys opinions?
Logged

Offline Lt.Del

  • Andy aka:SgtDel
  • Senior Member
  • ****
  • Posts: 3864
  • DelbridgePhotography.com
    • www.delbridge.net
Re: Shaking problem
« Reply #1 on: January 16, 2011, 12:10:00 am »
check your engine mounts and trans mounts to ensure your drive train is secure.

Check your lug nuts in all wheels (tighten)
 
Make sure your wheel isn't cracked

Logged

Offline topp

  • Frequent Member
  • **
  • Posts: 498
Re: Shaking problem
« Reply #2 on: January 16, 2011, 06:05:41 am »
Check your Ujoints as well
Logged
'90 Suburban TBI 350

Offline Irish_Alley

  • Tim
  • Senior Member
  • ****
  • Posts: 13333
  • Family is not an important thing. It's everything.
Re: Shaking problem
« Reply #3 on: January 16, 2011, 08:49:49 am »
Once it starts to shake does it happen at a speed or rpm. Try to get it to shake going down the road note what Rpm its turning. Stop then put it in first and match rpms see what it does if they ain't to high
Logged
If you can’t tell yourself the truth, who can you tell it to?~Irish_Alley

When you have eliminated the impossible, whatever remains, however improbable, must be the truth ~Sherlock Holmes

Offline Slammed83

  • Newbie
  • Posts: 18
Re: Shaking problem
« Reply #4 on: January 16, 2011, 02:28:46 pm »
Well i got on it this morning and it made a ping-ing noise. So im checking my torque converter to flywheel bolts.. And transmission cross member bolts.
Logged

Offline Irish_Alley

  • Tim
  • Senior Member
  • ****
  • Posts: 13333
  • Family is not an important thing. It's everything.
Re: Shaking problem
« Reply #5 on: January 16, 2011, 03:20:49 pm »
Check ujoints had one fall apart it would ping and the driveshaft would make the ping louder
Logged
If you can’t tell yourself the truth, who can you tell it to?~Irish_Alley

When you have eliminated the impossible, whatever remains, however improbable, must be the truth ~Sherlock Holmes

Offline bake74

  • Senior Member
  • ****
  • Posts: 5871
    • Build Thread
Re: Shaking problem
« Reply #6 on: January 16, 2011, 08:14:08 pm »
     x2 on what irish said, that sounds like what happened.
Logged
#1: The easiest and most obvious solution to any problem is 99% of the time correct.
#2: There is no such thing as impossible, it just takes longer.
  74 k10, 77k10    Tom

Offline bobcooter

  • Junior Member
  • ***
  • Posts: 788
  • 1979 Scottsdale C-20
Re: Shaking problem
« Reply #7 on: January 16, 2011, 08:34:49 pm »
X 3 on what Irish said. Look there first.
Logged
'79 C-20, 350/400, 3:73 gears, 9 leafs and a headache rack
Favorite Quote, "Good judgement comes from experience. Experience comes from poor judgement."

Offline Slammed83

  • Newbie
  • Posts: 18
Re: Shaking problem
« Reply #8 on: January 17, 2011, 04:36:32 pm »
crawled under there about an hour ago. I am really suprised it hasnt broken but the transmission shifted to the left, And you can see where the drive shaft has hit the heat sheld for the cat.. And where it bolts to the rear dif, The bolts were loose.
Logged

Offline Lt.Del

  • Andy aka:SgtDel
  • Senior Member
  • ****
  • Posts: 3864
  • DelbridgePhotography.com
    • www.delbridge.net
Re: Shaking problem
« Reply #9 on: January 17, 2011, 10:50:24 pm »
Quote
the transmission shifted to the left,


Quote
check your engine mounts and trans mounts to ensure your drive train is secure.


Why did Irish get all the votes on this one?  
LOL
I think everyone got this one right--loose u joints due to the ubolts being loose and broken insulator Trans mount.

I had that problem before, the noise scared the crap out of me when the driveshaft hits the cat heat shield when I turn right, and each turn of the driveshaft created another bang.

Click here
« Last Edit: January 17, 2011, 11:07:54 pm by SgtDel »
Logged

Offline Grim 82

  • Senior Member
  • ****
  • Posts: 1651
Re: Shaking problem
« Reply #10 on: January 18, 2011, 09:14:23 am »
I agree with SgtDel, lol

Makes you want to go front to back and top to bottom torquing every bolt now, I bet.
Logged
Give a man a gun, and he might rob a bank. Give a man a bank, and he might rob the world.

Offline Lt.Del

  • Andy aka:SgtDel
  • Senior Member
  • ****
  • Posts: 3864
  • DelbridgePhotography.com
    • www.delbridge.net
Re: Shaking problem
« Reply #11 on: January 18, 2011, 01:17:04 pm »
Thanks Grim, i got a vote, yeehaw!!!
« Last Edit: January 18, 2011, 07:41:52 pm by SgtDel »
Logged

Offline bobcooter

  • Junior Member
  • ***
  • Posts: 788
  • 1979 Scottsdale C-20
Re: Shaking problem
« Reply #12 on: January 19, 2011, 12:31:08 pm »
It was the pinging Sarge. That's what threw me. I've heard that sound before.
Logged
'79 C-20, 350/400, 3:73 gears, 9 leafs and a headache rack
Favorite Quote, "Good judgement comes from experience. Experience comes from poor judgement."

Offline Irish_Alley

  • Tim
  • Senior Member
  • ****
  • Posts: 13333
  • Family is not an important thing. It's everything.
Re: Shaking problem
« Reply #13 on: January 20, 2011, 05:19:58 pm »
I think they voted for me cause I'm never wrong  ;D
Logged
If you can’t tell yourself the truth, who can you tell it to?~Irish_Alley

When you have eliminated the impossible, whatever remains, however improbable, must be the truth ~Sherlock Holmes

Offline Lt.Del

  • Andy aka:SgtDel
  • Senior Member
  • ****
  • Posts: 3864
  • DelbridgePhotography.com
    • www.delbridge.net
Re: Shaking problem
« Reply #14 on: January 20, 2011, 05:43:04 pm »
Quote
I think they voted for me cause I'm never wrong  

and the above quote is correct?  :o
Logged
Pages: [1] 2   Go Up
« previous next »