« previous next »
Pages: [1]   Go Down

Author Topic: Wiring and Brake Questions! Noob!  (Read 3632 times)

Offline AJII

  • Newbie
  • Posts: 9
Wiring and Brake Questions! Noob!
« on: August 05, 2011, 06:11:05 pm »
Hey Guys,

My Dad and I recently acquired an 85 K10 with a blown engine. We're putting in a carb'ed 5.3 and I have a few questions about wiring and other misc things..and I'm sure as time goes on I'll have a lot more questions!  ;D

We noticed on the front brakes that the outside pad was not contacting the rotor, the inner pad was doing all the work. Would this be a bad caliper or bad master cylinder? It's doing the same thing on both sides.

The vacuum ball thats on the driver side..what does this do? Right now, it's connected to the windshield wiper fluid bottle, but this doesn't seem correct?

And I believe this is the wiring for the oil pressure sender and dummy light? Am I correct? The plug on one is new, but they are connected.



Thanks for any help you can give!
« Last Edit: August 05, 2011, 06:13:33 pm by AJII »
Logged

Offline DustyRusty

  • Junior Member
  • ***
  • Posts: 567
Re: Wiring and Brake Questions! Noob!
« Reply #1 on: August 05, 2011, 06:17:45 pm »
Sounds like both your calipers are bad.  I'd replace both w/ reman'd or new and w/ new pads.  They aren't that expensive.

Can't help you on the wiring.  Someone will be along to help you on that.

Rusty

P.S. Welcome from Alaska
Logged
1975 K-10 SWB Fleetside - 350/SM465/NP205/D44F 12-boltR, 3.73 gears.  Original owner.
Customized by rust.

Offline Blazin

  • Blazin new trails!
  • Senior Member
  • ****
  • Posts: 6130
Re: Wiring and Brake Questions! Noob!
« Reply #2 on: August 05, 2011, 07:18:10 pm »
The round plug is the oil pressuer gage / light. The other works the choke, its been a while since I have messed with one but it has something to do with the choke.
The brakes sound like the slides are stuck. Pull the calipers off, and compress them. If they return smoothly I would try wire wheeling the slides / bolts etc. Lube them up with brake grease, do pads and rotors if they need it though.
Logged
Some people are like Slinkies. Not really good for anything, but they still bring a smile to your face when you push them down a flight of stairs

Offline Dr_Snooz

  • Junior Member
  • ***
  • Posts: 684
  • "I like to take hammers, and just break stuff"
Re: Wiring and Brake Questions! Noob!
« Reply #3 on: August 05, 2011, 10:13:06 pm »
x2 on caliper guide pins.
Logged
1989 Chevy Suburban V-2500, 5.7L, TH400

1990 Chevy C-3500 Ext. Cab, 7.4L, 3L80

2009 Chevy Silverado 1500 WT 4WD, 4.8L, 4L60

Offline Irish_Alley

  • Tim
  • Senior Member
  • ****
  • Posts: 13333
  • Family is not an important thing. It's everything.
Re: Wiring and Brake Questions! Noob!
« Reply #4 on: August 05, 2011, 10:54:40 pm »
slide pins for sure
Logged
If you can’t tell yourself the truth, who can you tell it to?~Irish_Alley

When you have eliminated the impossible, whatever remains, however improbable, must be the truth ~Sherlock Holmes

Offline bake74

  • Senior Member
  • ****
  • Posts: 5871
    • Build Thread
Re: Wiring and Brake Questions! Noob!
« Reply #5 on: August 06, 2011, 10:55:23 am »
Quote from: Blazin on August 05, 2011, 07:18:10 pm
The round plug is the oil pressuer gage / light. The other works the choke, its been a while since I have messed with one but it has something to do with the choke.
 

   As blazin said, if memory serves me right, the second pic is for the fast idle electonic cam for the carb.
Logged
#1: The easiest and most obvious solution to any problem is 99% of the time correct.
#2: There is no such thing as impossible, it just takes longer.
  74 k10, 77k10    Tom

Offline jaredts

  • Senior Member
  • ****
  • Posts: 1330
Re: Wiring and Brake Questions! Noob!
« Reply #6 on: August 06, 2011, 09:29:34 pm »
The smaller is an oil pressure switch.  It completes the circuit for the choke heater so that the heater starts to open the choke once the engine is running (once oil pressure builds).  Electronic cam???
Logged

Offline AJII

  • Newbie
  • Posts: 9
Re: Wiring and Brake Questions! Noob!
« Reply #7 on: August 07, 2011, 04:32:57 pm »
Thanks guys!

I bet all of you are right on the money about the slides. The entire underside of the truck was covered in mud, so I bet they are caked and stuck.

I dug around the harness some more, and found what I believe to be the other plug for the oil sending unit, it's a rubber connector just like the other, but has just one pin instead of two.

Thanks for all your help!
Logged
Pages: [1]   Go Up
« previous next »