« previous next »
Pages: 1 [2]   Go Down

Author Topic: I have no idea??  (Read 19848 times)

Offline Greybeard

  • Frequent Member
  • **
  • Posts: 462
  • Newbie
Re: I have no idea??
« Reply #15 on: January 25, 2014, 10:55:45 pm »
Quote from: swilliams on January 17, 2014, 03:10:58 pm
Then on the other side of the block I have this any suggestions.

It looks like the oil sender to me. I had one like it on my 86 Blazer. Not saying that that's what it is but it looks the same. It's low on the passenger side it seems.
Logged
I am what I am and I ain't no more!

Offline swilliams

  • Frequent Member
  • **
  • Posts: 269
Re: I have no idea??
« Reply #16 on: January 26, 2014, 12:33:02 am »
That is the end of the starter to the left. I think I am getting ready to peel all the wire loom off and try and find a wiring diagram that actually shows all wires and where they are from and where they go. Any ideas
Logged

Offline bake74

  • Senior Member
  • ****
  • Posts: 5871
    • Build Thread
Re: I have no idea??
« Reply #17 on: January 26, 2014, 08:49:57 am »
Logged
#1: The easiest and most obvious solution to any problem is 99% of the time correct.
#2: There is no such thing as impossible, it just takes longer.
  74 k10, 77k10    Tom

Online bd

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 6600
Re: I have no idea??
« Reply #18 on: January 26, 2014, 01:34:42 pm »


Quote from: Boone83K10 on January 17, 2014, 06:29:46 pm
...The second pic looks like a knock sensor....

I agree.

The manuals linked by bake74 will be invaluable to you.
« Last Edit: January 26, 2014, 01:37:12 pm by bd »
Logged
Rich
It's difficult to know just how much you don't know until you know it.
In other words... if people learn by making mistakes, by now I should know just about everything!!!
87 R10 Silverado Fleetside 355 MPFI 700R4 3.42 Locker (aka Rusty, aka Mater)

Offline swilliams

  • Frequent Member
  • **
  • Posts: 269
Re: I have no idea??
« Reply #19 on: January 26, 2014, 09:14:33 pm »
Thanks for that
Logged

Offline Captkaos

  • OWNER and Administrator
  • Administrator
  • Senior Member
  • *****
  • Posts: 18461
    • http://www.73-87chevytrucks.com
Re: I have no idea??
« Reply #20 on: January 27, 2014, 09:09:46 pm »
That is a Knock Sensor.
Logged

Offline swilliams

  • Frequent Member
  • **
  • Posts: 269
Re: I have no idea??
« Reply #21 on: January 28, 2014, 11:48:59 pm »
Is it for the ESC
Logged

Online bd

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 6600
Re: I have no idea??
« Reply #22 on: January 29, 2014, 12:18:41 am »
Yes.
Logged
Rich
It's difficult to know just how much you don't know until you know it.
In other words... if people learn by making mistakes, by now I should know just about everything!!!
87 R10 Silverado Fleetside 355 MPFI 700R4 3.42 Locker (aka Rusty, aka Mater)

Offline swilliams

  • Frequent Member
  • **
  • Posts: 269
Re: I have no idea??
« Reply #23 on: January 29, 2014, 11:13:52 pm »
I think I have been advised to switch to a 4 pin distributor which would make ESC obsolete. I did not know this it might make things simpler.
Logged

Offline Captkaos

  • OWNER and Administrator
  • Administrator
  • Senior Member
  • *****
  • Posts: 18461
    • http://www.73-87chevytrucks.com
Re: I have no idea??
« Reply #24 on: February 03, 2014, 10:13:17 pm »
Just bypass the ESC it is much easier...  You have a number of threads all over the place on the same issue.  Next time please keep them together.
Logged

Offline swilliams

  • Frequent Member
  • **
  • Posts: 269
Re: I have no idea??
« Reply #25 on: February 12, 2014, 08:25:59 pm »
I have not tried to spread out they just kind of all ran together. Sorry
Logged
Pages: 1 [2]   Go Up
« previous next »