« previous next »
Pages: [1] 2   Go Down

Author Topic: Possible axle knuckle or yoke question  (Read 9449 times)

Offline moshrider3

  • Newbie
  • Posts: 15
  • Newbie
Possible axle knuckle or yoke question
« on: June 16, 2016, 08:02:55 am »
Hi everyone, this is my first time posting here so if in doing anything wrong please let me know. Recently I purchased a 1977 gmc k10 and have been doing some work to it.

I wanted to do a quick rotor and brake change but did not know how much work was involved. Anyway, I'm having trouble figuring out what I need, or the name of the part I'm looking it. The picture is attached below



I believe it is the yoke and the larger part connected to the hub is the knuckle? I noticed one of the rubber seals or maybe bushing was ripped apart, I tried to show it best in the picture.
If anyone knows what part or parts kit I need, it would be greatly appreciated. Thanks!


Sent from my iPhone using Tapatalk
Logged

Offline Irish_Alley

  • Tim
  • Senior Member
  • ****
  • Posts: 13333
  • Family is not an important thing. It's everything.
Re: Possible axle knuckle or yoke question
« Reply #1 on: June 16, 2016, 08:18:55 am »
that would be a lower ball joint. you dont have to change them to change the rotors. we do have a write up that may help
Logged
If you can’t tell yourself the truth, who can you tell it to?~Irish_Alley

When you have eliminated the impossible, whatever remains, however improbable, must be the truth ~Sherlock Holmes

Offline Irish_Alley

  • Tim
  • Senior Member
  • ****
  • Posts: 13333
  • Family is not an important thing. It's everything.
Re: Possible axle knuckle or yoke question
« Reply #2 on: June 16, 2016, 08:24:54 am »
Logged
If you can’t tell yourself the truth, who can you tell it to?~Irish_Alley

When you have eliminated the impossible, whatever remains, however improbable, must be the truth ~Sherlock Holmes

Offline moshrider3

  • Newbie
  • Posts: 15
  • Newbie
Re: Possible axle knuckle or yoke question
« Reply #3 on: June 16, 2016, 09:13:41 am »
Ah okay thanks for the information


Sent from my iPhone using Tapatalk
Logged

Offline moshrider3

  • Newbie
  • Posts: 15
  • Newbie
Re: Possible axle knuckle or yoke question
« Reply #4 on: June 16, 2016, 09:14:32 am »
The reason I'm changing it is because of the tear in that rubber piece


Sent from my iPhone using Tapatalk
Logged

Offline moshrider3

  • Newbie
  • Posts: 15
  • Newbie
Re: Possible axle knuckle or yoke question
« Reply #5 on: June 16, 2016, 09:16:37 am »
Quote from: Irish_Alley on June 16, 2016, 08:18:55 am
that would be a lower ball joint. you dont have to change them to change the rotors. we do have a write up that may help
Does it make a difference if the axle is a Dana 44, don't they have kingpins instead of ball joints?


Sent from my iPhone using Tapatalk
Logged

Offline Irish_Alley

  • Tim
  • Senior Member
  • ****
  • Posts: 13333
  • Family is not an important thing. It's everything.
Re: Possible axle knuckle or yoke question
« Reply #6 on: June 16, 2016, 10:16:16 am »
afaik only the dana 60 would have a kingpin. never seen a 44 with the kingpin. that one link is a 2wd so its a slightly different setup but its pretty much the same setup
Logged
If you can’t tell yourself the truth, who can you tell it to?~Irish_Alley

When you have eliminated the impossible, whatever remains, however improbable, must be the truth ~Sherlock Holmes

Offline moshrider3

  • Newbie
  • Posts: 15
  • Newbie
Re: Possible axle knuckle or yoke question
« Reply #7 on: June 16, 2016, 10:19:00 am »
Quote from: Irish_Alley on June 16, 2016, 10:16:16 am
afaik only the dana 60 would have a kingpin. never seen a 44 with the kingpin. that one link is a 2wd so its a slightly different setup but its pretty much the same setup
Okay thank you for the info, it looks pretty straightforward. I figured while I have everything off I might as well replace it now.


Sent from my iPhone using Tapatalk
Logged

Offline Irish_Alley

  • Tim
  • Senior Member
  • ****
  • Posts: 13333
  • Family is not an important thing. It's everything.
Re: Possible axle knuckle or yoke question
« Reply #8 on: June 16, 2016, 10:22:44 am »
yes and maybe u joints for the axle shafts if theyre sloppy
Logged
If you can’t tell yourself the truth, who can you tell it to?~Irish_Alley

When you have eliminated the impossible, whatever remains, however improbable, must be the truth ~Sherlock Holmes

Offline moshrider3

  • Newbie
  • Posts: 15
  • Newbie
Re: Possible axle knuckle or yoke question
« Reply #9 on: June 16, 2016, 11:48:43 am »
Ok, it looks like this would be the correct one? The one with the red arrow. I'll have to check them when I get home


Sent from my iPhone using Tapatalk
Logged

Offline Irish_Alley

  • Tim
  • Senior Member
  • ****
  • Posts: 13333
  • Family is not an important thing. It's everything.
Re: Possible axle knuckle or yoke question
« Reply #10 on: June 16, 2016, 12:13:34 pm »
i would go with the 371 due to the fact no fitting. the hole for the fitting some tend to think it makes a weak spot for them to break. i cant verify this but ive heard more than one person talk about it even the off road tv shows
Logged
If you can’t tell yourself the truth, who can you tell it to?~Irish_Alley

When you have eliminated the impossible, whatever remains, however improbable, must be the truth ~Sherlock Holmes

Offline hatzie

  • Junior Member
  • ***
  • Posts: 771
Re: Possible axle knuckle or yoke question
« Reply #11 on: June 17, 2016, 09:37:15 am »
Under normal operating conditions the hole for the grease fitting will not make a bit of difference.
It'd be nice if the joints could be had with low profile fittings in the caps.
Logged
SVC & wiring mans --> Here http://tinyurl.com/7387BRD-SVCMAN or My Bucket @ http://tinyurl.com/SQ-SVCMAN
Parts & Illustr Books -->http://tinyurl.com/SqParts
GMSTG Textbooks-->http://tinyurl.com/STG-TEXTBK
Radio Manuals-->http://tinyurl.com/DELCORADSVC

Offline Peter S

  • Newbie
  • Posts: 29
  • Newbie
Re: Possible axle knuckle or yoke question
« Reply #12 on: June 17, 2016, 10:23:21 am »
Quote from: hatzie on June 17, 2016, 09:37:15 am
Under normal operating conditions the hole for the grease fitting will not make a bit of difference.
It'd be nice if the joints could be had with low profile fittings in the caps.

They are available...MOOG p/n 377


Logged
-Peter

1978 K10 stepside

Offline Irish_Alley

  • Tim
  • Senior Member
  • ****
  • Posts: 13333
  • Family is not an important thing. It's everything.
Re: Possible axle knuckle or yoke question
« Reply #13 on: June 17, 2016, 12:44:57 pm »
ive seen them have a screw to remove then you have to put a zerk fitting in it when you want to grease. i think thats the style from moog
Logged
If you can’t tell yourself the truth, who can you tell it to?~Irish_Alley

When you have eliminated the impossible, whatever remains, however improbable, must be the truth ~Sherlock Holmes

Offline Peter S

  • Newbie
  • Posts: 29
  • Newbie
Re: Possible axle knuckle or yoke question
« Reply #14 on: June 17, 2016, 06:53:49 pm »
This is a joint from MOOG. It has a grease fitting installed that requires filling with a needle.

Logged
-Peter

1978 K10 stepside
Pages: [1] 2   Go Up
« previous next »