« previous next »
Pages: [1]   Go Down

Author Topic: 1985 GMC Sierra 4x4 front axle  (Read 6104 times)

Offline Fourxbob

  • Newbie
  • Posts: 34
  • Newbie
1985 GMC Sierra 4x4 front axle
« on: October 05, 2016, 12:00:15 pm »
I got a snap ring on the passenger side axle but not on driver's side. For some reason on the driver's side, the groove in the axle where the snap ring would go is too far towards the inner side. Could this axle be from a different make or model truck, or am I just going about it wrong?

Sent from my LGL44VL using Tapatalk

Logged

Offline Irish_Alley

  • Tim
  • Senior Member
  • ****
  • Posts: 13333
  • Family is not an important thing. It's everything.
Re: 1985 GMC Sierra 4x4 front axle
« Reply #1 on: October 08, 2016, 08:16:25 am »
have you reached behind the spindle where the u joint is and tried to push the axle out any?
Logged
If you can’t tell yourself the truth, who can you tell it to?~Irish_Alley

When you have eliminated the impossible, whatever remains, however improbable, must be the truth ~Sherlock Holmes

Offline Fourxbob

  • Newbie
  • Posts: 34
  • Newbie
Re: 1985 GMC Sierra 4x4 front axle
« Reply #2 on: October 12, 2016, 06:52:02 pm »
Yeah. I tried that. Disassembled it all today found out all I needed to do was  pry it up a little and then out. But I also found out I need all new bearings too.

Sent from my LGL44VL using Tapatalk

Logged

Offline Fourxbob

  • Newbie
  • Posts: 34
  • Newbie
Re: 1985 GMC Sierra 4x4 front axle
« Reply #3 on: October 16, 2016, 03:00:19 pm »
Still bad news. After installation of new axle bearing, inner and outer wheel bearings and seal. For some reason I still have the same problem. passenger side axle, the groove for the snap ring is only set in a 1/4" and on the driver's side it's a 1/2". Is that the way it's supposed to be?

Sent from my LGL44VL using Tapatalk

Logged

Offline Fourxbob

  • Newbie
  • Posts: 34
  • Newbie
Re: 1985 GMC Sierra 4x4 front axle
« Reply #4 on: October 16, 2016, 05:08:47 pm »
Quote from: Irish_Alley on October 08, 2016, 08:16:25 am
have you reached behind the spindle where the u joint is and tried to push the axle out any?
Just broke out the old Haynes manual. According to them the snap ring goes on before the lock out. If that's so the i guess I was doing it all wrong. Oops. Lol

Sent from my LGL44VL using Tapatalk

Logged

Offline Blazin

  • Blazin new trails!
  • Senior Member
  • ****
  • Posts: 6130
Re: 1985 GMC Sierra 4x4 front axle
« Reply #5 on: October 20, 2016, 07:48:29 am »
I have run several truck for a period of time without the snap ring even there. Not knowing it until I took it apart for axle joint, or pack the bearings.
Logged
Some people are like Slinkies. Not really good for anything, but they still bring a smile to your face when you push them down a flight of stairs

Offline Fourxbob

  • Newbie
  • Posts: 34
  • Newbie
Re: 1985 GMC Sierra 4x4 front axle
« Reply #6 on: October 20, 2016, 08:37:18 am »
Apparently i have to. This thing has sat for almost 10 years and if I remember right thats when I lost the snap ring to begin with. Only drove it for a year with new bearings in the same side.    Cant figure out why they need replaced again if that wasn't the cause.

Sent from my LGL44VL using Tapatalk

Logged

Offline Irish_Alley

  • Tim
  • Senior Member
  • ****
  • Posts: 13333
  • Family is not an important thing. It's everything.
Re: 1985 GMC Sierra 4x4 front axle
« Reply #7 on: October 20, 2016, 09:30:19 am »
i know weve cut a new grove for a snap ring
Logged
If you can’t tell yourself the truth, who can you tell it to?~Irish_Alley

When you have eliminated the impossible, whatever remains, however improbable, must be the truth ~Sherlock Holmes

Offline Fourxbob

  • Newbie
  • Posts: 34
  • Newbie
Re: 1985 GMC Sierra 4x4 front axle
« Reply #8 on: October 20, 2016, 09:44:47 am »
I'm just confused as to why its on the outside of the lockout on one side and on in the inner side on the drivers side.

Sent from my LGL44VL using Tapatalk

Logged
Pages: [1]   Go Up
« previous next »