73-87chevytrucks.com

Welcome to 73-87chevytrucks.com

73-87chevytrucks.com is not only a forum we are also a vendor for a variety of parts both replacement and custom. Check out our store at 73-87chevytrucks.com Online Store

73-87chevytrucks Social Network

We are also on Facebook so give us a like to the page if you like what you see: http://www.facebook.com/7387chevytrucks

73-87chevytrucks Merchandise

SpreadShop Site

Cafepress Site

Quadrajet Replacement

July 08, 2025, 12:27:25 pm by Rapid Roy
Views: 212 | Comments: 5

Planning to replace the Carter Q-jet soon. Wanting to replace with new. Have not purchased new before, only had rebuild. Is there anything special needed to be done prior to install?

TIA

Read More | Write Comment

Possible symptoms from a blocked rear diff. vent tube

July 02, 2025, 10:17:00 pm by philo_beddoe
Views: 282 | Comments: 2

Curious, what problems/symptoms could occur from a clogged up rear diff. vent tube?

Read More | Write Comment

Blower motor

July 02, 2025, 06:56:09 pm by Happytexan | Views: 290 | Comments: 3

Hello all. This is my first post on the forum. Truck data first: 1974 C10 Cheyenne super, factory 454, factory a/c still working (with an issue), th400, 2wd, factory 3:73 12 bolt out back.

the a/c blows ice cold but only blows on high. That was the only issue with the a/c until I remounted the recirc door actuator someone had left dangling so they could install kick panels with speakers now the recirc door operates as it should, but it still only blows on high and it stops blowing after 10~20 minutes, then will start blowing again if I turn the a/c off and back on. Sounds like a circuit breaker to me, but I can’t find one. I have replaced the resistor, blower relay, and blower motor. Not firing the parts cannon, just freshening things up while I’m in there. Side note, key on engine off, the blower blows on low speed like it should. As soon as I slide the mode switch from off to a/c it stops blowing, if it’s acting up. Is there a circuit breaker for the blower motor I’m not seeing? Do I need to pull the hvac control panel and dive into that? I greatly appreciate your time and help.

Read More | Write Comment

Key Cylinder In Column Won't Turn - Can't Start Truck

July 01, 2025, 09:06:54 am by ehjorten
Views: 635 | Comments: 11

So I went to start my '77 K20 the other day. I haven't driven it much lately and it has just been sitting. When I went to start it, the key wouldn't rotate out of the Off position. It would freely rotate to the ACC position and the radio would come on. It feels like the cylinder would move, but the rod linking the cylinder to the ignition switch is bound up or something. It all worked fine the last time I drove it. Any suggestions? I know I probably have to lower the column, but maybe something simple I am not thinking about?

Read More | Write Comment

Sanding/buffing/polishing

June 30, 2025, 05:45:50 pm by whipper.snapper | Views: 394 | Comments: 2

Hey yall, I have a question regarding polishing my paint.

My process right now has been to Sand the little bit of orange peel that I have starting with 800 or 1000 and ending on 2000 or 3000ish.

Following the sanding I start with 3M perfect-it rubbing compound with a foam pad on a rotary polisher, and then finish it up with the 3M perfect-it machine polish.

The problem: there will still be scratches showing after using the rubbing compound, do I need a more aggressive cutting compound? Do I need to go higher in sandpaper grit? Or do I just need more elbow grease and do more rounds of rubbing compound?

Also, if y’all wanted to let me know what your favorite cutting/polishing compound is that would be great. This is my first time.

Thank you in advance!

Sent from my iPhone using Tapatalk

Read More | Write Comment

Pages: [1]