« previous next »
Pages: [1]   Go Down

Author Topic: flip kit probs?  (Read 6905 times)

Offline antihero13

  • Newbie
  • Posts: 9
flip kit probs?
« on: February 20, 2011, 06:11:08 pm »
I bought my truck with the flip kit all ready done but it seems the back sit lower then the front by a little bit but also seems to sit a little lower on the passenger side. I took a look and this is what i found.
passenger side shackle(note the bend in the leaf)

here is the passenger hanger

and the driver hanger

I'm new to full size truck lowering so I don't know if everything looks right or not.
Logged

Offline autofreak

  • Newbie
  • Posts: 22
Re: flip kit probs?
« Reply #1 on: February 20, 2011, 06:21:17 pm »
if it is sitting lower on the pass side then it is def the bent main leaf. but there really is no bad thing about doing a flip, provided it is done correctly. i would def get the leaf replaced soon tho.
Logged

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19180
Re: flip kit probs?
« Reply #2 on: February 20, 2011, 06:25:23 pm »
Time for new springs. Make sure the shackles move freely.
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline topp

  • Frequent Member
  • **
  • Posts: 498
Re: flip kit probs?
« Reply #3 on: February 20, 2011, 06:32:14 pm »
Looks like both sides are bent....

Replace springs...
Logged
'90 Suburban TBI 350

Offline chevymotocross

  • Newbie
  • Posts: 95
Re: flip kit probs?
« Reply #4 on: February 20, 2011, 07:10:55 pm »
Missing a bolt on that last pic. The bracket for the leafs. Those springs look horrible!
Logged
1987 Chevy Silverado 2wd SWB: 305 TBI, 700r4, dual exhaust, tbi mods, k&n filter, belltech sway bar

Offline antihero13

  • Newbie
  • Posts: 9
Re: flip kit probs?
« Reply #5 on: February 20, 2011, 10:05:23 pm »
Yeah I thought they were junk but I wanted to get some input before I bought some new ones. I'm gonna have a look around for some replacements A.S.A.P. Thanks for the help all!
Logged

Offline bake74

  • Senior Member
  • ****
  • Posts: 5871
    • Build Thread
Re: flip kit probs?
« Reply #6 on: February 21, 2011, 04:50:35 pm »
Quote from: VileZambonie on February 20, 2011, 06:25:23 pm
Time for new springs. Make sure the shackles move freely.

     More than likely the shackle isn't moving and bent your leafs.
Logged
#1: The easiest and most obvious solution to any problem is 99% of the time correct.
#2: There is no such thing as impossible, it just takes longer.
  74 k10, 77k10    Tom

Offline beastie_3

  • Senior Member
  • ****
  • Posts: 3170
  • Josh
    • My truck pics
Re: flip kit probs?
« Reply #7 on: February 21, 2011, 06:36:45 pm »
Or someone overloaded the truck, or just took a torch to them.
Logged

Offline chevymotocross

  • Newbie
  • Posts: 95
Re: flip kit probs?
« Reply #8 on: February 21, 2011, 07:23:50 pm »
I recommend Energy Suspension poly bushings for the leaf springs and shackles. I installed them when I did the flip and shackle drop on my truck. Great quality!
Logged
1987 Chevy Silverado 2wd SWB: 305 TBI, 700r4, dual exhaust, tbi mods, k&n filter, belltech sway bar

Offline antihero13

  • Newbie
  • Posts: 9
Re: flip kit probs?
« Reply #9 on: February 22, 2011, 01:23:24 am »
I think this poor truck has lived many lives, looks like someone had a 5th wheel in the bed so weight was more then likely the cause but I'm not gonna rule out some shoddy lowering "tricks" lol.
Logged

Offline N2TRUX

  • Registered Users
  • *
  • Posts: 234
Re: flip kit probs?
« Reply #10 on: February 23, 2011, 08:47:27 pm »
It could have been overloaded, "or" the PO heated the springs to get more drop. Replace those and check your front springs too.
Logged

Offline antihero13

  • Newbie
  • Posts: 9
Re: flip kit probs?
« Reply #11 on: February 24, 2011, 02:31:00 am »
I hope to have the new leafs on this weekend. I did have a look at the front springs and it looks like they where cut but it's hard to tell how much. On the plus side the cut on the front springs look real good. something tells me even after I get the new leafs on it's still gonna ride low in the rear.........may have to pick up some lowering spindles at some point.
Logged
Pages: [1]   Go Up
« previous next »