« previous next »
Pages: [1]   Go Down

Author Topic: th400 swap questions  (Read 5458 times)

Offline ncguy89

  • Newbie
  • Posts: 74
    • My 4x4 Club
th400 swap questions
« on: May 15, 2012, 12:32:58 pm »
ok guys i got another question. i got a 84 chevy k10 with a th350/np203 converted. im swapping in a th400/208 into the truck. i know the th350/203 was not factory in this truck but it was in the truck when i bought it. now these are my questions.

1. the np203 in the truck has a slip yoke on the rear driveshaft. can i reuse this driveshaft and have a 32 spline yoke put on it for the np208?

2. instead of a cable i know the th400 has a solenoid. what is this switch that goes on the gas pedal called so i can buy one? is it called the trans kickdown solenoid switch (http://www.rockauto.com/catalog/moreinfo.php?pk=45109)?

3. the np203 in the truck now has 2 square rubber mounts. i bought a mount through oreilly's part number 2638 because its like the mounts i have seen before. will this mount work for the th400?

any help is greatly appreciated and if i can get these questions answered then i can have my dd back up and running in a day. thanks alot guys!!!
« Last Edit: May 15, 2012, 12:40:13 pm by ncguy89 »
Logged
1987 v20 - 350 tbi with towing cam, hummer wheels, stock otherwise

1984 chevy c-10 shortbed - kidney foundation truck (for my father)

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19175
Re: th400 swap questions
« Reply #1 on: May 15, 2012, 08:03:49 pm »
search on here for detent solenoid
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline ncguy89

  • Newbie
  • Posts: 74
    • My 4x4 Club
Re: th400 swap questions
« Reply #2 on: May 15, 2012, 09:43:25 pm »
i figured out the switch i needed. now for the other 2 questions can anyone help?
Logged
1987 v20 - 350 tbi with towing cam, hummer wheels, stock otherwise

1984 chevy c-10 shortbed - kidney foundation truck (for my father)

Offline bake74

  • Senior Member
  • ****
  • Posts: 5871
    • Build Thread
Re: th400 swap questions
« Reply #3 on: May 16, 2012, 06:28:34 am »
      There is a difference in length between the two trans and transfer case setups.  So your drive shaft will have to shortened. (depending on how long your tail shaft is on your th350, they came in different lengths).
      From what I can remember, the 208 at my shop and the 203 in my truck looked like they have the same or close to the same rubber mount for the cross member.  But I have not yet did the switch so I am not positive.
Logged
#1: The easiest and most obvious solution to any problem is 99% of the time correct.
#2: There is no such thing as impossible, it just takes longer.
  74 k10, 77k10    Tom

Offline ncguy89

  • Newbie
  • Posts: 74
    • My 4x4 Club
Re: th400 swap questions
« Reply #4 on: May 16, 2012, 11:17:21 am »
ok i appreciate the help. ill get it over to the ds shop today.
Logged
1987 v20 - 350 tbi with towing cam, hummer wheels, stock otherwise

1984 chevy c-10 shortbed - kidney foundation truck (for my father)

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19175
Re: th400 swap questions
« Reply #5 on: May 20, 2012, 04:34:09 pm »
Do you have the shifter and the crossmember for the 208? Your best bet is a donor. Is this a long or short bed?
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline ncguy89

  • Newbie
  • Posts: 74
    • My 4x4 Club
Re: th400 swap questions
« Reply #6 on: May 20, 2012, 08:37:58 pm »
yea i had all of that. i got everything in just waiting on the rear driveshaft and got to fix a wiring
problem.
Logged
1987 v20 - 350 tbi with towing cam, hummer wheels, stock otherwise

1984 chevy c-10 shortbed - kidney foundation truck (for my father)
Pages: [1]   Go Up
« previous next »