« previous next »
Pages: [1]   Go Down

Author Topic: LOWER CONTROL ARMS --- VS. --- DROP SPRINDLES  (Read 6853 times)

Offline okuma

  • Frequent Member
  • **
  • Posts: 362
LOWER CONTROL ARMS --- VS. --- DROP SPRINDLES
« on: January 10, 2009, 02:57:03 pm »
I plan on installing air suspension in the near future to my truck.

My question is  what would be a better choice and why if I install  3'' lower control arms    or    if i install 3''drop spindles.
 thnxs guys !
Logged
THE LOWER I GO,..... THE MORE SHE LIKES IT!

Offline three8six

  • Frequent Member
  • **
  • Posts: 486
Re: LOWER CONTROL ARMS --- VS. --- DROP SPRINDLES
« Reply #1 on: January 10, 2009, 05:20:49 pm »
I would suggest the spindles even though to run the factorys you have to modify the LCA's. They will keep you're truck in alignment. The LCA's are as bad as the lowering coil springs from what I've seen with keeping you're truck in alignment.
Logged

Offline Captkaos

  • OWNER and Administrator
  • Administrator
  • Senior Member
  • *****
  • Posts: 18461
    • http://www.73-87chevytrucks.com
Re: LOWER CONTROL ARMS --- VS. --- DROP SPRINDLES
« Reply #2 on: January 12, 2009, 04:33:59 pm »
they are both good.  I have both on current vehicles.  I haven't had alignment problems with either.  Generally LCA's only go down 2.5" where spindles can be had at 3".
Logged

Offline okuma

  • Frequent Member
  • **
  • Posts: 362
Re: LOWER CONTROL ARMS --- VS. --- DROP SPRINDLES
« Reply #3 on: January 13, 2009, 11:29:36 pm »
is it true?   i have heard that with spindles your front tires are further out . ???
Logged
THE LOWER I GO,..... THE MORE SHE LIKES IT!

Offline Captkaos

  • OWNER and Administrator
  • Administrator
  • Senior Member
  • *****
  • Posts: 18461
    • http://www.73-87chevytrucks.com
Re: LOWER CONTROL ARMS --- VS. --- DROP SPRINDLES
« Reply #4 on: January 13, 2009, 11:58:54 pm »
Spindles will increase the track width by about .25" per side, but if you have custom wheels with custom backspacing it isn't going to matter.

I just re-read your post and if I were going airbags, I would do the spindles.  Someone posted that CPP's spindles don't modify the track width.
Logged

Offline ms4972

  • Newbie
  • Posts: 41
Re: LOWER CONTROL ARMS --- VS. --- DROP SPRINDLES
« Reply #5 on: January 18, 2009, 08:32:55 pm »
Drop spindles are definately the way to go.  Better geometry and suspension travel. 

It's true about most drop spindles widening your track.  I've seen some that push you out as much as 3/4" on each side.  I just put a set of the CPP spindles on my '75 and it narrowed my track width.  I can finally make a u-turn.
Logged

Offline okuma

  • Frequent Member
  • **
  • Posts: 362
Re: LOWER CONTROL ARMS --- VS. --- DROP SPRINDLES
« Reply #6 on: January 24, 2009, 06:16:42 am »
THANKS guys , where can i get myself cpp spindles what are they 3" drop ?
Logged
THE LOWER I GO,..... THE MORE SHE LIKES IT!

Offline Captkaos

  • OWNER and Administrator
  • Administrator
  • Senior Member
  • *****
  • Posts: 18461
    • http://www.73-87chevytrucks.com
Re: LOWER CONTROL ARMS --- VS. --- DROP SPRINDLES
« Reply #7 on: January 24, 2009, 11:18:54 am »
Logged

Offline okuma

  • Frequent Member
  • **
  • Posts: 362
Re: LOWER CONTROL ARMS --- VS. --- DROP SPRINDLES
« Reply #8 on: February 27, 2009, 12:20:51 pm »
i contacted these guys fromm cpp but if i go the cpp route ..... i would need to replace to 1.25" rotors and calipers because i have 1" in place right now
Logged
THE LOWER I GO,..... THE MORE SHE LIKES IT!

Offline Chevalade

  • Frequent Member
  • **
  • Posts: 329
Re: LOWER CONTROL ARMS --- VS. --- DROP SPRINDLES
« Reply #9 on: March 20, 2009, 04:52:50 pm »
Quote from: okuma on February 27, 2009, 12:20:51 pm
i contacted these guys fromm cpp but if i go the cpp route ..... i would need to replace to 1.25" rotors and calipers because i have 1" in place right now


_6087DBK - Bracket kit to work with factory disc brakes and CPP Modular Spindles


Ryan
Logged
Pages: [1]   Go Up
« previous next »