« previous next »
Pages: [1]   Go Down

Author Topic: Factory Ride  (Read 4558 times)

Offline Strange81Z

  • Newbie
  • Posts: 15
    • My 81 Camaro Z28 T-TOP
Factory Ride
« on: January 24, 2009, 10:28:14 am »
Guys,

Just doing a little research.

Have any of you replaced your body bushings and control arm bushings to restore you factory "smooth ride" (The best I can anyway)?  When I get a truck that will be one of the first things I want to do, but I will also drop the ride some too.  Not by much though, maybe 2" drop in front and 1" drop in the rear.  I want the truck to have a slight rake.  Is there a kit that would do all of this at the same time?

Thanks,
Shawn
Logged

Offline Captkaos

  • OWNER and Administrator
  • Administrator
  • Senior Member
  • *****
  • Posts: 18461
    • http://www.73-87chevytrucks.com
Re: Factory Ride
« Reply #1 on: January 24, 2009, 11:10:53 am »
You are going to have to get the bushings and the lowering pieces seperately, but possibly from the same source.
Logged

Offline rockable

  • Registered Users
  • *
  • Posts: 210
  • Truckin', like the do-dah man.
Re: Factory Ride
« Reply #2 on: January 29, 2009, 04:50:26 pm »
These guys have a lot of kits.  You can browse here and learn a lot.  My '86's bushings were still in really good shape, so I didn't replace them.  My experience with plastic bushings in control arms on various cars, is that they ride a little rougher than the rubber bushings.  The older ones squeaked during the winter but the new compounds are a lot better about that.

www.stylintrucks.com
Logged
'86 SWB Silverado

Offline HAULIN IT

  • Senior Member
  • ****
  • Posts: 1542
Re: Factory Ride
« Reply #3 on: January 29, 2009, 05:42:35 pm »
Hopefully Sux responds, He can give you the best advice on the shift linkage  ;) I couldn't help it, I almost pee'd myself typing. Sorry Sux, All in good fun!
Logged

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19180
Re: Factory Ride
« Reply #4 on: January 29, 2009, 05:51:39 pm »
Quote from: HAULIN IT on January 29, 2009, 05:42:35 pm
Hopefully Sux responds, He can give you the best advice on the shift linkage  ;) I couldn't help it, I almost pee'd myself typing. Sorry Sux, All in good fun!

Huh? ???
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline HAULIN IT

  • Senior Member
  • ****
  • Posts: 1542
Re: Factory Ride
« Reply #5 on: February 01, 2009, 07:35:44 am »
I was poking fun at Sux (He has the nice looking Yellow shortbed) A while back, he posted about changing cab bushing, then a few days later, about the linkage wouldn't go into "low". After several days & some discussions ( I assumed he got it fixed) it wouldn't hold the truck in "park". After some more ( Again assuming he got it fixed) he came on...still not right. Then a month or Two later, better, but still not right. I'm sure this has been a frustrating experience for him, but he seems to have a pretty thick skin, so I was just working him over a little. Lorne   
Logged

Offline Flamingbig10

  • Frequent Member
  • **
  • Posts: 340
Re: Factory Ride
« Reply #6 on: February 24, 2009, 01:39:29 am »
I replaced both, when I replaced the body bushing the cab was the only thing on the frame so it made it easy and used floor jacks
Here is my truck with a 2-1 well worn factory coils with 1 coil cut,   and the over load was removed
« Last Edit: February 24, 2009, 01:51:37 pm by Flamingbig10 »
Logged
Pages: [1]   Go Up
« previous next »