« previous next »
Pages: [1]   Go Down

Author Topic: Trans. Kick down harness  (Read 4425 times)

Offline kfoz

  • Registered Users
  • *
  • Posts: 177
  • ALWAYS BUILD WITH BRICK & STONE ! ! !
Trans. Kick down harness
« on: March 06, 2009, 06:28:06 pm »
The elec. trans kick down is missing from my truck. I assume this is this a small separate harness that goes to the carb?  I need one and don't want to steal the one off my '74.

kfoz
Logged
kfoz (kfoz@comcast.net)
'73 C20 4 Speed 2WD

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19180
Re: Trans. Kick down harness
« Reply #1 on: March 07, 2009, 07:13:49 am »
TH400? The switch goes on the gas pedal.
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline kfoz

  • Registered Users
  • *
  • Posts: 177
  • ALWAYS BUILD WITH BRICK & STONE ! ! !
Re: Trans. Kick down harness
« Reply #2 on: March 07, 2009, 11:44:20 am »
What about a 350/350 set up? My gas pedal does have the steel bracket which the kick down does snap into.

kfoz
Logged
kfoz (kfoz@comcast.net)
'73 C20 4 Speed 2WD

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19180
Re: Trans. Kick down harness
« Reply #3 on: March 07, 2009, 12:07:46 pm »
That's a detent cable, no wiring harness there
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline kfoz

  • Registered Users
  • *
  • Posts: 177
  • ALWAYS BUILD WITH BRICK & STONE ! ! !
Re: Trans. Kick down harness
« Reply #4 on: March 07, 2009, 12:15:06 pm »
So then, I assume it is NOT directly hooked to the pedal but on the carb itself??

Logged
kfoz (kfoz@comcast.net)
'73 C20 4 Speed 2WD

Offline 78 Chevyrado

  • Z62 ON-ROAD
  • Site Supporters
  • Senior Member
  • ******
  • Posts: 2748
    • My Photobucket Site
Re: Trans. Kick down harness
« Reply #5 on: March 07, 2009, 04:34:11 pm »
Here's you a pic.  You just run 12v+ from the fuse panel to it, and then to the single electrical connector on the drivers side of the tranny.  you'll need the gas pedal bracket from an original th400 truck.

Logged
Kenny

1978 C-20, 350/400, 3.73, Graystone Metallic, Raceline Renegade 8 Wheels - 18x8.5, 275/70R18 BFG KO's

Offline kfoz

  • Registered Users
  • *
  • Posts: 177
  • ALWAYS BUILD WITH BRICK & STONE ! ! !
Re: Trans. Kick down harness
« Reply #6 on: March 07, 2009, 04:53:59 pm »
Thanks but as I said my truck has a TH350 and it does have a gas pedal bracket but nothing electrical is attached. My '74 454/400 has what you spoke of, BUT, where does this DETENT CABLE go for the TH350??

kfoz
Logged
kfoz (kfoz@comcast.net)
'73 C20 4 Speed 2WD

Offline 78 Chevyrado

  • Z62 ON-ROAD
  • Site Supporters
  • Senior Member
  • ******
  • Posts: 2748
    • My Photobucket Site
Re: Trans. Kick down harness
« Reply #7 on: March 07, 2009, 05:58:16 pm »
detent cable for a th350 goes from the throttle bracket on the carb to the tranny, theres nothing electric involved.  I though you were installing a 400 in your truck, sorry.
Logged
Kenny

1978 C-20, 350/400, 3.73, Graystone Metallic, Raceline Renegade 8 Wheels - 18x8.5, 275/70R18 BFG KO's

Offline kfoz

  • Registered Users
  • *
  • Posts: 177
  • ALWAYS BUILD WITH BRICK & STONE ! ! !
Re: Trans. Kick down harness
« Reply #8 on: March 07, 2009, 11:38:10 pm »
No problem, thanks very much for your help.

kfoz
Logged
kfoz (kfoz@comcast.net)
'73 C20 4 Speed 2WD
Pages: [1]   Go Up
« previous next »