Author Topic: 79 stepside 5.3l/4L60-E Swap (Read 91456 times)

Captkaos · « **Reply #60 on:** January 08, 2010, 02:15:36 pm »

There is only 1 crossmember for the trucks, for different transmissions, you just move it.

Mtrhd329 · « **Reply #61 on:** January 08, 2010, 08:09:33 pm »

using the stock crossmember just have to drill some new holes. The keyless portion of my keyless chuck drill broke so i need a new one before i can get that finished. I got my wiring hooked up and my fuse block and relay center installed. Battery cables and radiator hooked up. Also started messing around in HP tuners.

Captkaos · « **Reply #62 on:** January 08, 2010, 11:08:51 pm »

Be careful messing around. You can really screw something up with it.

Mtrhd329 · « **Reply #63 on:** January 09, 2010, 01:03:17 am »

Mainly just reading and looking at all of the functions this program has not really anything to do yet as i havent fired the motor yet.

Any one know what manifolds fit the 73-87's I have been reading for hours and cant seem to find anything on 73-87s just 62-72s
F-body? vette? trailblazer?

Captkaos · « **Reply #64 on:** January 11, 2010, 04:22:16 pm »

LS manifolds? I used the factory 6.0L manifolds. If you get the later ones they should fit also (truck ones)

87OldYeller · « **Reply #65 on:** January 11, 2010, 05:20:52 pm »

header from summit part# SUM-G908 $153.93 they are shorty headers fit 99-04 truck requires slight mods to PASS side rail, u can either cut the rail, or what i am going to do is take the header have it cut right above the flange and add about 2 inches of pipe in so it will clear.

Mtrhd329 · « **Reply #66 on:** January 11, 2010, 06:56:07 pm »

do these headers have egr provisions? I am having a problem finding ones that fit but ALSO have egr.....might just need some made up but then they wont have a CARB EO# to pass smog

87OldYeller · « **Reply #67 on:** January 11, 2010, 07:15:54 pm »

that i do not know but member here aussie. he could tell you better i dont know what all he is running.

fptransport · « **Reply #68 on:** January 13, 2010, 10:53:12 pm »

good build man.... I am about to start on mine. could you tell me where you found the info to make your harness work? I used to have a lot of links saved on my computer but I have a new one now so all I had saved was lost

. but seriously nice truck

87OldYeller · « **Reply #69 on:** January 14, 2010, 11:45:19 am »

well u just have to kinda figure out what you need. I am gonna run stock exhaust so i am keeping 02 Sensors, i am going to get rid of EGR and all Evap stuff. don't know what else yet.but member here Aussie he is a huge help and has a ton of info he has his complete and running.

Mtrhd329 · « **Reply #70 on:** January 24, 2010, 12:25:18 pm »

so i got my manifolds to fit. I cut the egr port off the stock manifold and welded a patch panel onto it. Then i took the egr mounting base and made a flange and welded a pipe to it and that mounts just above where the stock egr mount was. Now i have clearance. Found that the rear of the manifold still rubs but i will notch the frame and clearance the manifold and i should be fine. Everything still fit under the stock heat sheild so it looks factory still but i have my clearance. Now on to the gas pedal and e-fans.

Mtrhd329 · « **Reply #71 on:** March 03, 2010, 07:59:44 pm »

So i got it to fire tonight turns out my PCM connector was not tightened down all the way. I had been troubleshooting 3 different circuits for weeks and then i tightened the connector up and it fired right up. Well now it is on to the last few things i need to tighten up or bolt on and then take it for a drive. Started scanning with my HP tuners so i will be looking over the tune and seeing what i need to do from there.

Captkaos · « **Reply #72 on:** March 03, 2010, 08:05:29 pm »

sweet

Jims86tpisub · « **Reply #73 on:** March 04, 2010, 03:11:19 pm »

Where did you get that killer deal on the drivetrain....Cali?

Mtrhd329 · « **Reply #74 on:** March 04, 2010, 09:44:46 pm »

There is a local yard that sells motors and i talked him into selling everything for the swap. now he has a listing on craiglist for swaps..lol

News: