« previous next »
Pages: [1]   Go Down

Author Topic: Truck now runs on 6 or 7 cylinders after carb swap  (Read 4033 times)

Offline ar3366

  • New Users
  • Posts: 1
Truck now runs on 6 or 7 cylinders after carb swap
« on: November 09, 2009, 08:41:02 pm »
I have a 79 GMC Sierra.. has a 350 and a quadrajet.. I just took that carb off for a edelbrock 600..since I have made that swap the truck acts like it has a dead cylinder or two. Runs really really ruff... and won't also sustain any real rpm with out chokeing out on fuel or something.. I don't understand if I bought a bad carb.. or did I accidently hurt my engine with I mis adjusted the timeing shortly there after... I'm totally at a loss.. I've tryed just about everything I could think of.. please help
Logged

Offline Captkaos

  • OWNER and Administrator
  • Administrator
  • Senior Member
  • *****
  • Posts: 18466
    • http://www.73-87chevytrucks.com
Re: Truck now runs on 6 or 7 cylinders after carb swap
« Reply #1 on: November 09, 2009, 08:45:49 pm »
Was the Edelbrock new?
Was the Q-jet bad?
Have you check the plugs?
Logged

Offline Lt.Del

  • Andy aka:SgtDel
  • Senior Member
  • ****
  • Posts: 3864
  • DelbridgePhotography.com
    • www.delbridge.net
Re: Truck now runs on 6 or 7 cylinders after carb swap
« Reply #2 on: November 09, 2009, 10:21:20 pm »
i wouldn't think you hurt your engine by midadjusting the timing.  Engines are pretty tough.

did you remove any plug wires during this carb change?  You have to rule one thing out at a time.  Ensure plug wires follow the firing order of a small block chevy.

Air/fuel mix correct?  no vacuum leak (carb gasket, hose knocked off)? clogged jet? Cracked distributor cap? Timing correct now? And, what Chris said
Logged

Offline HAULIN IT

  • Senior Member
  • ****
  • Posts: 1542
Re: Truck now runs on 6 or 7 cylinders after carb swap
« Reply #3 on: November 10, 2009, 09:26:32 pm »
Do you have a spreadbore intake? The Edelbrock/AFB may not be sealing on the sides of the back barrels. There is a plate to seal this off...Q-jet gasket on the intake, plate, Edel/AFB gasket, carb. Just a thought, Lorne
Logged

Offline team39763

  • Senior Member
  • ****
  • Posts: 1194
Re: Truck now runs on 6 or 7 cylinders after carb swap
« Reply #4 on: November 16, 2009, 11:37:27 am »
Did you forget the big vacuum hose?  I did that one time when I swapped my carb and it ran like crap.  It wouldn't idle unless I revved it, it ran like crap.  Took me a few days to figure it out.
Logged

Offline joesgarage71

  • Wrench
  • Senior Member
  • ****
  • Posts: 1156
Re: Truck now runs on 6 or 7 cylinders after carb swap
« Reply #5 on: November 16, 2009, 04:12:10 pm »
 Sounds like something real simple, check your work
Logged
78' K-20 355/SM465/twin stick 205 6" on 36's
14 bolt FF/big bearing Dana 44 4.56 gears
92' GMC C-1500 454/4L80E/14 bolt

Offline thirsty

  • Senior Member
  • ****
  • Posts: 1289
    • Suitor's Garage
Re: Truck now runs on 6 or 7 cylinders after carb swap
« Reply #6 on: November 16, 2009, 05:56:04 pm »
pull your plugs and see whats going on.
Logged
Real trucks are built, not bought Build thread

Give me a long enough lever and a place to stand, and I shall move the earth or break this bolt...Whatever, just hold my beer!

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19189
Re: Truck now runs on 6 or 7 cylinders after carb swap
« Reply #7 on: November 16, 2009, 06:21:04 pm »
Quote from: team39763 on November 16, 2009, 11:37:27 am
Did you forget the big vacuum hose?  I did that one time when I swapped my carb and it ran like crap.  It wouldn't idle unless I revved it, it ran like crap.  Took me a few days to figure it out.

This is most likely what he did.
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10
Pages: [1]   Go Up
« previous next »