« previous next »
Pages: [1]   Go Down

Author Topic: Engine noise.  (Read 4541 times)

Offline 87OldYeller

  • Frequent Member
  • **
  • Posts: 366
Engine noise.
« on: November 18, 2009, 04:57:12 pm »
My fist though was valves rattling but i aint so sure. but while in gear the engine is making a rattle, I jacked up the rear axle blocked the front tires, started her up and put it in gear set the e-brake to apply some resistance, and the rattle appears to be in the driver side front on the engine. i do not have a/c so i know it is not a compressor. engine might have 10,000 total. 305 block small cam and new model vortec heads. later i amd gonna take off the fan and run it for a short min. just to reduce other noise to try to pin point it... any ideas ?
Logged

Offline 87OldYeller

  • Frequent Member
  • **
  • Posts: 366
Re: Engine noise.
« Reply #1 on: November 18, 2009, 05:20:34 pm »
sorry was in a hurry and didn't spell check on the first post.. but I removed the fan just now. Noise is still there but i can not tell where it is coming from. only does it in gear. in park or neutral not a sound. But in gear it rattles mostly when it shifts into 2nd gear.
Logged

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19181
Re: Engine noise.
« Reply #2 on: November 18, 2009, 06:16:43 pm »
So you hear it just idling in gear too? Is it pinging? Do you have a stethoscope?
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline 87OldYeller

  • Frequent Member
  • **
  • Posts: 366
Re: Engine noise.
« Reply #3 on: November 18, 2009, 06:29:35 pm »
no you do not hear it at idle or revering it in park or neutral. no i don't have that tool i know what it is i can borrow one from work though. but only in gear that is why i though it is kinda funny but i know for fact it is the engine.
Logged

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19181
Re: Engine noise.
« Reply #4 on: November 18, 2009, 09:13:26 pm »
Did you check your u-joints? Check your flexplate to converter bolts too.
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline 87OldYeller

  • Frequent Member
  • **
  • Posts: 366
Re: Engine noise.
« Reply #5 on: November 18, 2009, 09:59:35 pm »
OK i will check the flex plate bolts. i know it is not u joints. but i didn't even think of them bolts thanks alto.
Logged

Offline 87OldYeller

  • Frequent Member
  • **
  • Posts: 366
Re: Engine noise.
« Reply #6 on: November 19, 2009, 03:23:10 pm »
checked the bolts they were tight but i gave them a little more. but i did not drive it today and when i started up up today i was getting the rattle at start up and idle a little but while in park at about 2100RPM you can hear it good just sounds like valves kinda but once it warms up in park it is not to bad. I put some octane booster in it as well and drove it just now and no change. but it is in the back of the engine driver side... possible a lifter?
Logged

Offline Donut

  • Frequent Member
  • **
  • Posts: 402
Re: Engine noise.
« Reply #7 on: November 19, 2009, 03:59:54 pm »
Loose header tube?  I don't mean exhaust leak, but I forgot to retighten a couple of bolts, and I thought the engine was coming apart. (tube rattling against the head)

Lifter pre-load correct?
Logged
'73 Chevy K-20 ***SOLD***
350/tbh350/np205
My plow was half price if i took the truck with it.

'86 C-30 dually, 454/tbh400

Offline 87OldYeller

  • Frequent Member
  • **
  • Posts: 366
Re: Engine noise.
« Reply #8 on: November 19, 2009, 04:21:44 pm »
Lifter pre-load correct?   (Not sure what ya are asking or what that means) but i am gonna re check the header bolts. i am gone look over a few other things to.. but thanks and if anyone has any ideas please let me know.. i am gonna add some Lucas oil Stabilizer tomorrow just for s/g.
Logged

Offline 87OldYeller

  • Frequent Member
  • **
  • Posts: 366
Re: Engine noise.
« Reply #9 on: November 19, 2009, 04:58:23 pm »
I checked all header bolts some were not as tight as others but they are good now. i also had some play in the power steering Pump shaft so i took off the belt and ran it up the road again and the noise is still there, at about 2100RPM in park and really bad when it shifts to 2nd.
Logged
Pages: [1]   Go Up
« previous next »