« previous next »
Pages: 1 [2] 3   Go Down

Author Topic: Which bolts for NP205 front driveshaft  (Read 35918 times)

Offline Blazin

  • Blazin new trails!
  • Senior Member
  • ****
  • Posts: 6130
Re: Which bolts for NP205 front driveshaft
« Reply #15 on: August 06, 2011, 07:51:50 am »
16 should be the thread count. If the shaft has been out for any amount of time I would run a tap through the holes first.
Logged
Some people are like Slinkies. Not really good for anything, but they still bring a smile to your face when you push them down a flight of stairs

Offline Laderhosen

  • Frequent Member
  • **
  • Posts: 272
Re: Re: Which bolts for NP205 front driveshaft
« Reply #16 on: August 07, 2011, 05:19:02 pm »
Found em. They're UNC (Unified Coarse), the ones I had were UNF (Unified Fine). Anyway all sorted now so thanks for the advise. Got the driveshaft on.

Next question!!!!...
Is there any way of telling if my locking hubs are engaging???
Logged
'82 3/4 ton, 350, th400,
'88 K5 Blazer, 350, 700R4
’98 BMW 328i daily drive
’91 VW Golf Mk 2 with VR6 conv

Offline Irish_Alley

  • Tim
  • Senior Member
  • ****
  • Posts: 13333
  • Family is not an important thing. It's everything.
Re: Which bolts for NP205 front driveshaft
« Reply #17 on: August 07, 2011, 06:23:03 pm »
if both are lock your front shaft will be locked with the transfer case in neutral
Logged
If you can’t tell yourself the truth, who can you tell it to?~Irish_Alley

When you have eliminated the impossible, whatever remains, however improbable, must be the truth ~Sherlock Holmes

Offline Laderhosen

  • Frequent Member
  • **
  • Posts: 272
Re: Re: Re: Which bolts for NP205 front driveshaft
« Reply #18 on: August 07, 2011, 08:38:15 pm »
Quote from: Irish_Alley on August 07, 2011, 06:23:03 pm
if both are lock your front shaft will be locked with the transfer case in neutral

So would I be able to tell by putting it in 4 HI, then put the transfer case in neutral, jack the front axle and try to rotate one of the wheels by hand. If it doesn't budge the hubs are locked???
Logged
'82 3/4 ton, 350, th400,
'88 K5 Blazer, 350, 700R4
’98 BMW 328i daily drive
’91 VW Golf Mk 2 with VR6 conv

Offline 1979C20

  • Senior Member
  • ****
  • Posts: 1659
  • Kyle Taulton.
Re: Which bolts for NP205 front driveshaft
« Reply #19 on: August 07, 2011, 09:07:27 pm »
Put your transfer case in neutral, lock the hubs, jack the front end up and turn the wheel. If the drive shaft turns then they are locked. Make sure the truck is not going to roll, too.
Logged
1979 SCLB C20 Q-jet 350 SM465 14b F.F. 4.10 G80
1989 GMC Suburban V2500 TBI350 TH400 4in lift 35's 14b SF

Offline Blazin

  • Blazin new trails!
  • Senior Member
  • ****
  • Posts: 6130
Re: Which bolts for NP205 front driveshaft
« Reply #20 on: August 07, 2011, 09:37:33 pm »
Or you can jack each wheel up separately. Lock the hub rotate the wheel. If the axles turns its engaged. Unlock the wheel should roll without turning the axle. Transfer case does not need to be in neutral.
Logged
Some people are like Slinkies. Not really good for anything, but they still bring a smile to your face when you push them down a flight of stairs

Offline Irish_Alley

  • Tim
  • Senior Member
  • ****
  • Posts: 13333
  • Family is not an important thing. It's everything.
Re: Which bolts for NP205 front driveshaft
« Reply #21 on: August 08, 2011, 05:44:31 am »
for my way it does or in 4x2 and you dont have to jack it up
Logged
If you can’t tell yourself the truth, who can you tell it to?~Irish_Alley

When you have eliminated the impossible, whatever remains, however improbable, must be the truth ~Sherlock Holmes

Offline thirsty

  • Senior Member
  • ****
  • Posts: 1289
    • Suitor's Garage
Re: Which bolts for NP205 front driveshaft
« Reply #22 on: August 08, 2011, 10:16:43 am »
If they are manual locking hubs just lock one and reach around the tire and try to rotate the axle.
Logged
Real trucks are built, not bought Build thread

Give me a long enough lever and a place to stand, and I shall move the earth or break this bolt...Whatever, just hold my beer!

Offline Laderhosen

  • Frequent Member
  • **
  • Posts: 272
Re: Which bolts for NP205 front driveshaft
« Reply #23 on: August 08, 2011, 12:54:23 pm »
How does the actual locking hub engage??
Logged
'82 3/4 ton, 350, th400,
'88 K5 Blazer, 350, 700R4
’98 BMW 328i daily drive
’91 VW Golf Mk 2 with VR6 conv

Offline Irish_Alley

  • Tim
  • Senior Member
  • ****
  • Posts: 13333
  • Family is not an important thing. It's everything.
Re: Which bolts for NP205 front driveshaft
« Reply #24 on: August 08, 2011, 03:50:41 pm »
the lock pushes a sleeve with spines on both sides inward and that in turn locks the wheel hub to the axle shaft. its more simple than most would think
thanks ej
it pretty much pushes 11 into 12
« Last Edit: August 08, 2011, 03:54:08 pm by Irish_Alley »
Logged
If you can’t tell yourself the truth, who can you tell it to?~Irish_Alley

When you have eliminated the impossible, whatever remains, however improbable, must be the truth ~Sherlock Holmes

Offline beastie_3

  • Senior Member
  • ****
  • Posts: 3170
  • Josh
    • My truck pics
Re: Which bolts for NP205 front driveshaft
« Reply #25 on: August 08, 2011, 06:23:05 pm »
11 and 12 mesh together when locked, and 13 pushes 11 out when unlocked. 11 grabs the axle shaft, 12 grabs the hub.
Logged

Offline Blazin

  • Blazin new trails!
  • Senior Member
  • ****
  • Posts: 6130
Re: Which bolts for NP205 front driveshaft
« Reply #26 on: August 08, 2011, 11:00:45 pm »
Thirsty's way works too, but have had them have a bad spot in the hub. They could be locked in that postion, but partly, or completely disengaged in others.
« Last Edit: August 08, 2011, 11:02:37 pm by Blazin »
Logged
Some people are like Slinkies. Not really good for anything, but they still bring a smile to your face when you push them down a flight of stairs

Offline Laderhosen

  • Frequent Member
  • **
  • Posts: 272
Re: Re: Which bolts for NP205 front driveshaft
« Reply #27 on: August 10, 2011, 05:55:08 pm »
Quote from: Irish_Alley on August 08, 2011, 03:50:41 pm
the lock pushes a sleeve with spines on both sides inward and that in turn locks the wheel hub to the axle shaft. its more simple than most would think
thanks ej
it pretty much pushes 11 into 12

Thanks, so presumably when the drive shaft rotates, by 4wd being engaged, it locks the hub.
Logged
'82 3/4 ton, 350, th400,
'88 K5 Blazer, 350, 700R4
’98 BMW 328i daily drive
’91 VW Golf Mk 2 with VR6 conv

Offline beastie_3

  • Senior Member
  • ****
  • Posts: 3170
  • Josh
    • My truck pics
Re: Which bolts for NP205 front driveshaft
« Reply #28 on: August 10, 2011, 05:59:18 pm »
its gets locked when you turn the dial. when you turn the dial, it pushes #12 in, which meshes with #11. #13 spring pushes #12 out when the hubs are unlocked. #11 is stationary.
Logged

Offline Laderhosen

  • Frequent Member
  • **
  • Posts: 272
Re: Which bolts for NP205 front driveshaft
« Reply #29 on: August 10, 2011, 10:47:02 pm »
Quote from: beastie_3 on August 10, 2011, 05:59:18 pm
its gets locked when you turn the dial. when you turn the dial, it pushes #12 in, which meshes with #11. #13 spring pushes #12 out when the hubs are unlocked. #11 is stationary.

Mine are auto locking hubs though??
Logged
'82 3/4 ton, 350, th400,
'88 K5 Blazer, 350, 700R4
’98 BMW 328i daily drive
’91 VW Golf Mk 2 with VR6 conv
Pages: 1 [2] 3   Go Up
« previous next »