« previous next »
Pages: [1]   Go Down

Author Topic: Help ! Think I may have a really bad problem.  (Read 6411 times)

Offline Marvan c10

  • Newbie
  • Posts: 44
  • Newbie
Help ! Think I may have a really bad problem.
« on: December 18, 2011, 02:32:52 pm »
 I have a 1980 C10 with an 350 that was taken out of a 1985 K5 Blazer, it has a 4bbl rochester Q-jet carburetor that was rebuild. Yesterday I installed the carb started the truck it ran really rough and stall out. When I restarted it the same thing, ran rough and stall out but this time the engine jumped violently, and now it seems like something in the engine is stuck and won't allow it to crank at all. The numbers on the is 17058466
« Last Edit: December 18, 2011, 03:03:43 pm by Marvan c10 »
Logged
While we're speeding through life, we miss the chance to get a good look at the road we're on.

Offline firefighter

  • Frequent Member
  • **
  • Posts: 462
Re: Help ! Think I may have a really bad problem.
« Reply #1 on: December 18, 2011, 03:55:02 pm »
Possible the float is stuck in the carb and filled a cylinder with gas and now that cylinder can't make its way to the top because it can't evacuate the fuel.
Do you have an electric fuel pump? Do you smell gas?
You could try pulling the plugs and see if it would crank over then.
Anyone else thinking the same thing?
That's the only thing I can think that would not allow you to even get it turning over.
Logged

Offline Engineer

  • Senior Member
  • ****
  • Posts: 1402
Re: Help ! Think I may have a really bad problem.
« Reply #2 on: December 18, 2011, 04:14:51 pm »
Could be a hydrolock, but that would be a gob of gas.
Logged
2002 Chevy 2500HD 4x4 8.1/ZF6sp RC/LB
2001 Chevy 2500HD 4x4 6.0/4L85E EC/SB
1997 Chevy Blazer 4x4
1994 Chevy K-2500 4x4 C6P 5.7/4L80E
1979 Chevy K-30 4x4 4sp 4.10
1977 Chevy K-30 4x4 4sp 4.10 454

Dad of an Eagle Scout, and a Life Scout

Offline jaredts

  • Senior Member
  • ****
  • Posts: 1330
Re: Help ! Think I may have a really bad problem.
« Reply #3 on: December 18, 2011, 04:33:25 pm »
Starter?  Dead battery?  Can you turn it over by hand?
Logged

Offline Marvan c10

  • Newbie
  • Posts: 44
  • Newbie
Re: Help ! Think I may have a really bad problem.
« Reply #4 on: December 18, 2011, 05:17:17 pm »
 Weirdest thing ! I pulled the starter, nothing change then I pulled the fuel pump and heard a thump like something moved. And now it starts but still runs rough. Could it have been that the fuel pump arm was binding up and somehow holding the engine ?
Logged
While we're speeding through life, we miss the chance to get a good look at the road we're on.

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19179
Re: Help ! Think I may have a really bad problem.
« Reply #5 on: December 18, 2011, 05:29:27 pm »
check the firing order
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠¯¯¯¯¯'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline Marvan c10

  • Newbie
  • Posts: 44
  • Newbie
Re: Help ! Think I may have a really bad problem.
« Reply #6 on: December 18, 2011, 05:42:33 pm »
 The firing order should be the same on a 1980 350 and 1985 350, yes ?   1-8-4-3-6-5-7-2
Logged
While we're speeding through life, we miss the chance to get a good look at the road we're on.

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19179
Re: Help ! Think I may have a really bad problem.
« Reply #7 on: December 18, 2011, 06:07:29 pm »
yes
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠¯¯¯¯¯'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline bake74

  • Senior Member
  • ****
  • Posts: 5871
    • Build Thread
Re: Help ! Think I may have a really bad problem.
« Reply #8 on: December 18, 2011, 07:37:44 pm »
     Hey Marvin, what's up.  If you need help let me know, more than willing to help out.
Logged
#1: The easiest and most obvious solution to any problem is 99% of the time correct.
#2: There is no such thing as impossible, it just takes longer.
  74 k10, 77k10    Tom

Offline heavychevy91

  • Frequent Member
  • **
  • Posts: 322
  • '86 Chevy K20
Re: Help ! Think I may have a really bad problem.
« Reply #9 on: December 19, 2011, 05:23:00 pm »
Whats your timing set at? did you have the distributor out during the engine swap?
Logged

Offline Irish_Alley

  • Tim
  • Senior Member
  • ****
  • Posts: 13333
  • Family is not an important thing. It's everything.
Re: Help ! Think I may have a really bad problem.
« Reply #10 on: December 25, 2011, 12:59:45 am »
is your distributor 180 out?
Logged
If you can’t tell yourself the truth, who can you tell it to?~Irish_Alley

When you have eliminated the impossible, whatever remains, however improbable, must be the truth ~Sherlock Holmes

Offline Marvan c10

  • Newbie
  • Posts: 44
  • Newbie
Re: Help ! Think I may have a really bad problem.
« Reply #11 on: December 25, 2011, 04:47:07 pm »
 Marry Christmas everyone ! Yes I removed the distributor in the swap, when reinstalling I use my dads old school mather. Hand crank the engine till the # 1 cylinder was at TDC and without looking at distributor dropped it in, tighten it down crank the motor through one complete cycle pull the # 1 plug again hand crank to TDC remove the dist-cap and see that the rotor is pointing at the # 1 wire tower. Which it was, installed all the wires in there towers size accordingly number taped them and ran them to there appropriate plugs, check the timing and I was done.
Logged
While we're speeding through life, we miss the chance to get a good look at the road we're on.

Offline Lt.Del

  • Andy aka:SgtDel
  • Senior Member
  • ****
  • Posts: 3864
  • DelbridgePhotography.com
    • www.delbridge.net
Re: Help ! Think I may have a really bad problem.
« Reply #12 on: December 25, 2011, 06:30:03 pm »
i agree with Irish.  You may be firing on exhaust stroke.  just for giggles, put her back at TDC, remove wires from distributor and put #1 wire on the #6 spot on the distributor and continue around that way as if #6 was number 1.  See what happens.
« Last Edit: December 25, 2011, 06:32:18 pm by SgtDel »
Logged

Offline heavychevy91

  • Frequent Member
  • **
  • Posts: 322
  • '86 Chevy K20
Re: Help ! Think I may have a really bad problem.
« Reply #13 on: December 27, 2011, 06:00:42 pm »
Quote from: Irish_Alley on December 25, 2011, 12:59:45 am
is your distributor 180 out?

Quote from: SgtDel on December 25, 2011, 06:30:03 pm
i agree with Irish.  You may be firing on exhaust stroke.  just for giggles, put her back at TDC, remove wires from distributor and put #1 wire on the #6 spot on the distributor and continue around that way as if #6 was number 1.  See what happens.

You guys saved me a lot of typing!
Logged
Pages: [1]   Go Up
« previous next »