« previous next »
Pages: [1]   Go Down

Author Topic: How much for this bare block 350?  (Read 4804 times)

Offline bladerunner

  • Registered Users
  • *
  • Posts: 241
How much for this bare block 350?
« on: December 02, 2012, 03:49:44 pm »
Local guy has a 350 bare block, casting number 3970010. I was told it is a 1971 4 bolt main. It has never been bored over. Guy might be interested in selling it, but I have not asked pointedly yet. Just curious, what would this be worth, or what is a good offer? I want to rebuild the engine in my K10, but want to be able to use it when needed, so I was going to buy a separate block.
Logged
85 K10 Shortbed
94 Impala SS

Offline thirsty

  • Senior Member
  • ****
  • Posts: 1289
    • Suitor's Garage
Re: How much for this bare block 350?
« Reply #1 on: December 02, 2012, 04:16:33 pm »
Just a block with nothing else? $50 in my opinion if you can trust it is good.
If we lived a bit closer I would give you a block. It would cost you more than $50 to come get it though. ;D
Logged
Real trucks are built, not bought Build thread

Give me a long enough lever and a place to stand, and I shall move the earth or break this bolt...Whatever, just hold my beer!

Offline gildardo01

  • Frequent Member
  • **
  • Posts: 265
  • Newbie
Re: How much for this bare block 350?
« Reply #2 on: December 02, 2012, 05:28:33 pm »
Quote from: thirsty on December 02, 2012, 04:16:33 pm
Just a block with nothing else? $50 in my opinion if you can trust it is good.
If we lived a bit closer I would give you a block. It would cost you more than $50 to come get it though. ;D
yeah chevy 350 blocks are cheap... you can find them anywhere... just make sure it´s all in standard measurements and it isn´t cracked or anything
Logged

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19182
Re: How much for this bare block 350?
« Reply #3 on: December 02, 2012, 07:37:07 pm »
Agreed a bare 350 block and you're taking his word for it? Look carefully at the cylinder walls and the main bearing bore. Measure as well.
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline bladerunner

  • Registered Users
  • *
  • Posts: 241
Re: How much for this bare block 350?
« Reply #4 on: December 02, 2012, 09:33:49 pm »
No way to guarantee the block isn't cracked without paying for it be magnafluxed. But I guess all used blocks are a gamble to a certain degree.

Thirsty, you are in NH right?
Logged
85 K10 Shortbed
94 Impala SS

Offline Blazin

  • Blazin new trails!
  • Senior Member
  • ****
  • Posts: 6130
Re: How much for this bare block 350?
« Reply #5 on: December 02, 2012, 11:12:50 pm »
other thing is are the mains marked, or were they kept in order?
In my opinion if you are looking for a motor to rebuild get one that runs good, just tired, or smokes. That way you are 99.9% sure it won't yield a big suprise when you go to make it fresh again.
Logged
Some people are like Slinkies. Not really good for anything, but they still bring a smile to your face when you push them down a flight of stairs

Offline thirsty

  • Senior Member
  • ****
  • Posts: 1289
    • Suitor's Garage
Re: How much for this bare block 350?
« Reply #6 on: December 03, 2012, 06:08:46 am »
Logged
Real trucks are built, not bought Build thread

Give me a long enough lever and a place to stand, and I shall move the earth or break this bolt...Whatever, just hold my beer!

Offline bladerunner

  • Registered Users
  • *
  • Posts: 241
Re: How much for this bare block 350?
« Reply #7 on: December 03, 2012, 09:47:27 am »
Alright, well I will keep my eyes peeled for a better engine, hopefully one I can get dirt cheap.
Logged
85 K10 Shortbed
94 Impala SS

Offline bladerunner

  • Registered Users
  • *
  • Posts: 241
Re: How much for this bare block 350?
« Reply #8 on: December 04, 2012, 10:35:38 am »
So if I am looking for an engine that takes roller lifters, that is only the 87 and newer engines right? I understood that basically if it has a one-piece rear main, then the engine has a hydraulic roller cam, is that right?
Logged
85 K10 Shortbed
94 Impala SS

Offline Jason S

  • Senior Member
  • ****
  • Posts: 1561
Re: How much for this bare block 350?
« Reply #9 on: December 05, 2012, 08:11:11 pm »
One piece rear main seal began in 1986. The 1987 up would be a one piece rear main seal, but it may or may not actually have had a roller cam installed or even machined for a factory roller cam. Also, some of the early one-piece blocks may not have been drilled for using an engine driven fuel pump.
Logged
1973 GMC K2500, Super Custom, Camper Special, 350, TH350, NP203, 4.10's
1974 Chevrolet K10, Custom Deluxe, 350, SM465, NP203, 3.73's

"1) Peace through strength; 2) Trust but verify; 3) Beware of evil in the modern world"

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19182
Re: How much for this bare block 350?
« Reply #10 on: December 08, 2012, 09:16:20 am »
LT-1 or Vortec blocks will have what you're looking for
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10
Pages: [1]   Go Up
« previous next »