« previous next »
Pages: [1]   Go Down

Author Topic: newb with rust  (Read 5930 times)

Offline Joegibbstruck

  • Newbie
  • Posts: 20
  • Newbie
newb with rust
« on: April 21, 2017, 09:51:50 am »
So I'm new here, and bought this 79 c10. The bottom of it is completely rust free. There are a couple pin holes around the passenger side windshield, but once I got it home I found out the inner and outer cowl are rusted through and someone down the line attempted to put a later front clip on it. So they slotted the cowl for the hinges. I have all my parts catalogs ordered but they have not arrived yet. What I have looked at online, I can't find replacement panels for the cowl area. Do I need to be in the look out for a donor cab to steal these parts from, or does someone make these panels.











Logged

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19180
Re: newb with rust
« Reply #1 on: April 21, 2017, 10:24:24 am »
Donor or fabrication.
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠¯¯¯¯¯'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline FlatBlack77

  • Junior Member
  • ***
  • Posts: 894
  • Cheap Fast Reliable - Pick 2
Re: newb with rust
« Reply #2 on: April 21, 2017, 10:39:49 am »
Quote from: VileZambonie on April 21, 2017, 10:24:24 am
Donor or fabrication.

bingo.

either way aint going to be fun. thats a good bit of repair work
Logged
"When you are a hammer, everything looks like a nail"
'77 C/10 - 350/350 mild street motor

Offline Joegibbstruck

  • Newbie
  • Posts: 20
  • Newbie
Re: newb with rust
« Reply #3 on: April 21, 2017, 11:10:55 am »
I'm guessing I need a pre 81 if I want to go back to the 73-79 front clip. Found a 76 on craigslist for 800 for the entire truck, but I don't want an entire truck lol. Hoping someone has a cab laying around with no title that I can pick up for just a couple hundred bucks.
Logged

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19180
Re: newb with rust
« Reply #4 on: April 21, 2017, 04:41:11 pm »
Get the entire truck, take what you need and sell the rest or do a cab swap. You can post your spare parts in the classifieds section here or craigslist and make your money back.
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠¯¯¯¯¯'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline 1967KaiserM715

  • Junior Member
  • ***
  • Posts: 914
  • 1985 GMC K1500 w/ 6.5 TD
Re: newb with rust
« Reply #5 on: April 21, 2017, 07:09:56 pm »
Quote from: Joegibbstruck on April 21, 2017, 11:10:55 am
I'm guessing I need a pre 81 if I want to go back to the 73-79 front clip. Found a 76 on craigslist for 800 for the entire truck, but I don't want an entire truck lol. Hoping someone has a cab laying around with no title that I can pick up for just a couple hundred bucks.
Be careful with this, title normally follows the cab, unless your in a special state where it needs to be numbers matching. Meaning if at any point there may be a chance you need a title, it's better to have them legal.

I agree, try to get the whole truck-and because you now know some problem areas, you could find a better cab then yours and just do a whole cab swap.


Sent from my iPhone using Tapatalk
Logged
Current Vehicles:1985 GMC K10(Daily) 1991 GMC K2500(Daily) 1975 Beetle(not running) 1985 Mercedes 300D(not running) 1952 M35    1967 M715(not running)
 1986 Chevy K30(under repair)

Offline Joegibbstruck

  • Newbie
  • Posts: 20
  • Newbie
Re: newb with rust
« Reply #6 on: April 21, 2017, 10:07:48 pm »
Found a cab today that has what I need not rusted out. It has a title, but I'm just gonna cut it apart and scrap the rest. Paid 200 for cab with title, core support, and hood to go back to the 79-79 front end. I am not scared of body work. I have a 66 mustang in my garage that I have replaced 1/2 the car with replacement panels.
Logged

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19180
Re: newb with rust
« Reply #7 on: April 22, 2017, 06:15:37 am »
Save your vin plate and title before you scrap it.
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠¯¯¯¯¯'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline Irish_Alley

  • Tim
  • Senior Member
  • ****
  • Posts: 13333
  • Family is not an important thing. It's everything.
Re: newb with rust
« Reply #8 on: April 22, 2017, 08:28:05 am »
Quote from: VileZambonie on April 22, 2017, 06:15:37 am
Save your vin plate and title before you scrap it.
"AS TROPHIES" and dont tell anyone lol
Logged
If you can’t tell yourself the truth, who can you tell it to?~Irish_Alley

When you have eliminated the impossible, whatever remains, however improbable, must be the truth ~Sherlock Holmes

Offline Joegibbstruck

  • Newbie
  • Posts: 20
  • Newbie
Re: newb with rust
« Reply #9 on: April 30, 2017, 12:36:57 pm »
Got my replacement firewall yesterday, paid 230 for a spare cab, straight hood, coresupport, headlight bezels, and upper and lower grille trim. Now the task of coming up with a plan on doing the firewall swap. Think I'll cut the pillars where the factory joint is at the roof. As my passenger side has some rust on it.







Logged
Pages: [1]   Go Up
« previous next »