« previous next »
Pages: 1 ... 9 10 [11]   Go Down

Author Topic: Ready to be blasted  (Read 47447 times)

Offline macr0w

  • Registered Users
  • *
  • Posts: 130
  • Newbie
Re: Ready to be blasted
« Reply #150 on: June 11, 2023, 06:25:11 am »
Dude!!!
You are killing it.
That thing is going to be so nice when you finish it up.  8)
Logged

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19210
Re: Ready to be blasted
« Reply #151 on: June 11, 2023, 06:25:27 am »
Coming along nicely
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline Swampyankee74

  • Frequent Member
  • **
  • Posts: 327
  • Keep em alive
Re: Ready to be blasted
« Reply #152 on: June 11, 2023, 07:56:54 am »
Thank you. I've never been this deep into a vehicle.  There's a whole lot of learning going on. A lot of one step forward then 2 back haha

Sent from my SM-S515DL using Tapatalk

Logged

Offline Shifty

  • Senior Member
  • ****
  • Posts: 1095
  • I bleed Bowtie red...
Re: Ready to be blasted
« Reply #153 on: June 13, 2023, 09:25:21 am »
Looking great man!
Logged
87 V20 Standard Cab Longbed (current)

87 R30 3+3 Longbed (days of yore)

98 C2500 ext cab longbed

Offline Swampyankee74

  • Frequent Member
  • **
  • Posts: 327
  • Keep em alive
Re: Ready to be blasted
« Reply #154 on: June 18, 2023, 07:36:53 pm »
Msd 6al box is mounted. Just getting into some wiring. Ended up putting a low resistance hei bushing in the distributor (was recommended I do so). Removed the hei module. I needed keyed power to turn the msd box on and off, I ended up removing the resistor wire and pin from the bulkhead and soldered a 12 guage wire to the pin and put it back in the bulk head, this way I have full 12 volt not 8 or 9.
I'm going from a 3 wire alternator to a 1 wire. In what way do I hook this up so that my ammeter still functions? Or will it function with just the 1 wire?
Logged

Offline Swampyankee74

  • Frequent Member
  • **
  • Posts: 327
  • Keep em alive
Re: Ready to be blasted
« Reply #155 on: June 18, 2023, 08:25:05 pm »
Pic

Sent from my SM-S515DL using Tapatalk

Logged

Offline Chevynut73

  • Newbie
  • Posts: 85
  • Newbie
Re: Ready to be blasted
« Reply #156 on: June 30, 2023, 08:40:05 pm »
WOW - great build!

You are fixin to have one nice C10  :)

Are those 10" Cragar's on the rear?
Logged
'73 Chevy C10, 350, TH350, was a long Fleetside, now she's a short Stepper that's under construction (been in the Family since 1972).

Would rather push a CHEVY than drive a Furd

Offline Swampyankee74

  • Frequent Member
  • **
  • Posts: 327
  • Keep em alive
Re: Ready to be blasted
« Reply #157 on: June 30, 2023, 08:45:55 pm »
The rear rims are 15x8. But the 295/50 fits nice on them


Sent from my SM-S515DL using Tapatalk

Logged

Offline Swampyankee74

  • Frequent Member
  • **
  • Posts: 327
  • Keep em alive
Re: Ready to be blasted
« Reply #158 on: June 30, 2023, 09:07:08 pm »
Did what I can for wiring, time to put the nose on to keep going. Will take a little bit.  Frostbite electric fans are in the mail, that match the radiator I have

Sent from my SM-S515DL using Tapatalk

Logged

Offline Chevynut73

  • Newbie
  • Posts: 85
  • Newbie
Re: Ready to be blasted
« Reply #159 on: June 30, 2023, 09:17:47 pm »
Is that right - that 295/50 looks a lot better!

I have 15x8 Rally's that looked fine with the Fleetside but not so good with the Stepper!   
Logged
'73 Chevy C10, 350, TH350, was a long Fleetside, now she's a short Stepper that's under construction (been in the Family since 1972).

Would rather push a CHEVY than drive a Furd
Pages: 1 ... 9 10 [11]   Go Up
« previous next »