1
Welcome,
Guest
. Please
login
or
register
.
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
News:
Registration and Posting Agreement
Home
Forum
Store
Help
Search
Gallery
Login
Register
73-87chevytrucks.com
»
73-87 Chevy _ GMC Trucks
»
Brakes, Frame, Steering & Suspension
»
In-truck replacement of Power Steering Output shaft seal
« previous
next »
Print
Pages: [
1
]
Go Down
Author
Topic: In-truck replacement of Power Steering Output shaft seal (Read 3745 times)
JohnnyPopper
Senior Member
Posts: 2683
Old Goof
In-truck replacement of Power Steering Output shaft seal
«
on:
February 01, 2023, 06:41:21 PM »
Has anyone tried to replace this seal in-truck?
Looks feasible, but thought I would tap the brain trust before diving in.
TIA for your assistance!
Logged
1957 Apache 3100 235 Inline 6, 3 on the tree
1973 C-20, 3+3 454 4BBL TH400 Water Injection
1978 K-10, 350 4BBL TH350 NP203 M.M. Part time Kit/Hubs
1980 C-10 under construction
Mike81K10
Junior Member
Posts: 996
Re: In-truck replacement of Power Steering Output shaft seal
«
Reply #1 on:
February 01, 2023, 10:52:53 PM »
Are you talking about the one on the firewall? Have the seal and the two piece metal plates.
Logged
"Tell me and I forget. Teach me and I remember. Involve me and I learn." -Benjamin Franklin
JohnnyPopper
Senior Member
Posts: 2683
Old Goof
Re: In-truck replacement of Power Steering Output shaft seal
«
Reply #2 on:
February 02, 2023, 04:45:52 PM »
No, the actual shaft the pitman arm is bolted to.
The kit came with two seals, a flat washer, and snap ring.
Logged
1957 Apache 3100 235 Inline 6, 3 on the tree
1973 C-20, 3+3 454 4BBL TH400 Water Injection
1978 K-10, 350 4BBL TH350 NP203 M.M. Part time Kit/Hubs
1980 C-10 under construction
VileZambonie
Global Moderator
Senior Member
Posts: 19125
Re: In-truck replacement of Power Steering Output shaft seal
«
Reply #3 on:
February 02, 2023, 05:49:21 PM »
You mean the steering gear box. Usually when the seals start leaking there is play in the gearbox. With the wheels on the ground, have an assistant rock the steering wheel while you watch the sector shaft for play. If play exists, changing the seal will be a waste of time. Consider a reman unit if it is walloped. If it looks okay, remove the pitman arm, snap ring and have at it. Try not to scratch the shaft when doing it.
Logged
, ___
/ _ _ _\_
⌠¯¯¯¯¯' [☼===☼]
`()_);-;()_)--o--)_)
74 GMC
,
75 K5
,
84 GMC
,
85 K20
,
86 k20
,
79 K10
JohnnyPopper
Senior Member
Posts: 2683
Old Goof
Re: In-truck replacement of Power Steering Output shaft seal
«
Reply #4 on:
February 02, 2023, 07:01:49 PM »
I guess you're right, it really doesn't output anything
Thanks VZ, I'll do just that!
Logged
1957 Apache 3100 235 Inline 6, 3 on the tree
1973 C-20, 3+3 454 4BBL TH400 Water Injection
1978 K-10, 350 4BBL TH350 NP203 M.M. Part time Kit/Hubs
1980 C-10 under construction
MIKE S
Registered Users
Posts: 225
Member
Re: In-truck replacement of Power Steering Output shaft seal
«
Reply #5 on:
February 03, 2023, 09:11:24 AM »
It can be done. The best way after removing the pitman arm is to center the steering wheel and remove the four bolts on top that hold the pitman shaft cap to the housing. Tap the sector shaft gently from the bottom and pull the cap and shaft from the top. Do not disturb the adjustment nut on the top. You will need the repair kit that has the metal plate gasket for this type of repair. You will not loose any of the internal balls as long as you don’t turn the steering wheel after removal. You can also try the messy way by pulling the pitman arm then snap ring then start truck and tun steering wheel to the lock and use the internal pressure to “blow” the seal’s out. It doesn’t always work but you won’t know if you don’t try.
«
Last Edit: February 03, 2023, 09:32:38 AM by MIKE S
»
Logged
JohnnyPopper
Senior Member
Posts: 2683
Old Goof
Re: In-truck replacement of Power Steering Output shaft seal
«
Reply #6 on:
February 03, 2023, 12:48:44 PM »
Thanks Mike, never thought of 'blowing out' the seal.
I thought I would drill some small holes in the seal and use a slide hammer, like pulling out a dent.
Logged
1957 Apache 3100 235 Inline 6, 3 on the tree
1973 C-20, 3+3 454 4BBL TH400 Water Injection
1978 K-10, 350 4BBL TH350 NP203 M.M. Part time Kit/Hubs
1980 C-10 under construction
MIKE S
Registered Users
Posts: 225
Member
Re: In-truck replacement of Power Steering Output shaft seal
«
Reply #7 on:
February 03, 2023, 01:48:33 PM »
Make sure you wrap the splines with masking tape one wrap before installing seal.
Logged
JohnnyPopper
Senior Member
Posts: 2683
Old Goof
Re: In-truck replacement of Power Steering Output shaft seal
«
Reply #8 on:
February 03, 2023, 08:14:40 PM »
Ok, but what's the theory behind that?
Logged
1957 Apache 3100 235 Inline 6, 3 on the tree
1973 C-20, 3+3 454 4BBL TH400 Water Injection
1978 K-10, 350 4BBL TH350 NP203 M.M. Part time Kit/Hubs
1980 C-10 under construction
MIKE S
Registered Users
Posts: 225
Member
Re: In-truck replacement of Power Steering Output shaft seal
«
Reply #9 on:
February 03, 2023, 11:46:26 PM »
Not to cut the seals while slipping them up the shaft into the housing. Those splines are sharp.
Logged
JohnnyPopper
Senior Member
Posts: 2683
Old Goof
Re: In-truck replacement of Power Steering Output shaft seal
«
Reply #10 on:
February 05, 2023, 12:41:32 PM »
Ah...Good catch!
Thanks Mike!
Logged
1957 Apache 3100 235 Inline 6, 3 on the tree
1973 C-20, 3+3 454 4BBL TH400 Water Injection
1978 K-10, 350 4BBL TH350 NP203 M.M. Part time Kit/Hubs
1980 C-10 under construction
JohnnyPopper
Senior Member
Posts: 2683
Old Goof
Re: In-truck replacement of Power Steering Output shaft seal
«
Reply #11 on:
June 03, 2023, 03:48:32 PM »
Success! No wallop in the shaft so I dove in.
Couldn't pick the seals, so went Johnnpopper.
Drilled 1/16 hole in each seal, screwed in a fine thread drywall screw and pried out with dikes against the casing.
Blew out hole with brake cleaner.
Gently tapped the new ones in, using washer as surface so as not to dent the seal.
Tapped till they bottomed, inserted snap ring but too far into the casing.
Got it all cleaned up, parked, only to see oil dripping. Thought it must be residual, but NO, the snap ring, washer were sitting on the pitman arm and seal was starting to come out.
ROOKIE MISTAKE! Oh well, made sure it was correct the second time...
Logged
1957 Apache 3100 235 Inline 6, 3 on the tree
1973 C-20, 3+3 454 4BBL TH400 Water Injection
1978 K-10, 350 4BBL TH350 NP203 M.M. Part time Kit/Hubs
1980 C-10 under construction
Print
Pages: [
1
]
Go Up
« previous
next »
73-87chevytrucks.com
»
73-87 Chevy _ GMC Trucks
»
Brakes, Frame, Steering & Suspension
»
In-truck replacement of Power Steering Output shaft seal