« previous next »
Pages: [1]   Go Down

Author Topic: dent repair  (Read 2221 times)

Offline 84GMCSierra

  • Newbie
  • Posts: 27
  • Newbie
dent repair
« on: February 11, 2023, 07:57:40 am »
I have a large dent in the left side of my truck, next to the gas tank that I want to get out, but can't get to it from the back side. I tried one of those suction cup dent puller that won't stay on to pull it out. I know I could go to a body shop, but I can't afford that. Any other ideas you all have used?
Logged

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19151
Re: dent repair
« Reply #1 on: February 11, 2023, 10:10:32 am »
Use a PDR bladder, or lift the bed and work it out from the backside. Still may be easier to have PDR guy tackle it for you.
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline Mr Diesel

  • Frequent Member
  • **
  • Posts: 357
  • Aaron
Re: dent repair
« Reply #2 on: February 11, 2023, 01:00:49 pm »
I would leave it. Matches the dent in the front fender.
Logged
1976 C20 Crewcab, 6.2L/SM465
1982 K30 Crewcab , 427TD/TH400
1983 C30, 6.2L/TH400
1983 K30 Crewcab 454/700R4
1986 K10 350/400. 1989 K30 cab/chassis 454/SM465

Offline AZ4X4SQBDY

  • Registered Users
  • *
  • Posts: 149
  • Newbie
Re: dent repair
« Reply #3 on: February 11, 2023, 10:36:54 pm »
I have had "ok" luck with a PDR kit from Amazon that uses hot glue from an electric glue gun and a slide hammer with the pull tabs. Old squares actually have some steel there but take your time and keep at it. Every time you pull it off it moves a little, you may need to glue it 20 times and spend an hour to get it out.
This with an air shim from Home Depot used for shimming doors and windows should get it done.
Logged
1987 GMC Sierra Classic 4x4 short, fleet, 1985 Chevrolet Silverado 4x4 short, step side, '87 Chevy Silverado short fleet, '91 Dodge Ramcharger LE 4x4,
2005 Porsche Boxster S,1982 Alfa Romeo Spider Veloce

Offline 84GMCSierra

  • Newbie
  • Posts: 27
  • Newbie
Re: dent repair
« Reply #4 on: February 12, 2023, 06:00:41 am »
Quote from: AZ4X4SQBDY on February 11, 2023, 10:36:54 pm
I have had "ok" luck with a PDR kit from Amazon that uses hot glue from an electric glue gun and a slide hammer with the pull tabs. Old squares actually have some steel there but take your time and keep at it. Every time you pull it off it moves a little, you may need to glue it 20 times and spend an hour to get it out.
This with an air shim from Home Depot used for shimming doors and windows should get it done.
That fender isn't on the truck anymore. I sold it after replacing it with a Blazer fender. This picture is the day I bought the truck in Phoenix, November 2013
Logged
Pages: [1]   Go Up
« previous next »