« previous next »
Pages: [1]   Go Down

Author Topic: No Start TBI  (Read 113 times)

Offline catbird7

  • Newbie
  • Posts: 3
  • Newbie
No Start TBI
« on: July 14, 2025, 05:56:24 pm »
1987 R10 305 4spd manual 4x4. No pulse to injectors. So far I have purchased new fuel pump, new fuel filter, new fuel pump relay, completely new distributor, and new computer. Verified power at both ecm fuses and verified the fuses are good. Overriding the relay, forces the fuel pump to run and provides fuel pressure at the injectors however will not spray. 9 volt battery applied to injectors produces good spray  from both injectors and allows the engine to run but only until the initial sprayed fuel is burnt. I have no check engine light at all, and I pulled the instrument panel apart and verified the actual bulb for check engine light is good. I'm lost!
Logged

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19180
Re: No Start TBI
« Reply #1 on: July 14, 2025, 07:12:59 pm »
http://forum.73-87chevytrucks.com/smforum/index.php?topic=37738.0

If you are certain ECM B has power in and out of the fuse, check at the two cavities at the ECM as seen in the link I posted.
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline catbird7

  • Newbie
  • Posts: 3
  • Newbie
Re: No Start TBI
« Reply #2 on: July 15, 2025, 07:07:28 am »
Explain, "two cavities at the ecm"? You need to dumb this down for me.
Logged

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19180
Re: No Start TBI
« Reply #3 on: July 15, 2025, 01:43:50 pm »
Did you click the link?

Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline catbird7

  • Newbie
  • Posts: 3
  • Newbie
Re: No Start TBI
« Reply #4 on: July 15, 2025, 05:05:33 pm »
Yep, guess I'm sub 100.............
Logged

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19180
Re: No Start TBI
« Reply #5 on: July 15, 2025, 07:30:32 pm »
Follow the flow chart and study the diagram. Check the pinouts at the ECM if all 3 fuses have B+ on each side of the fuse. I am attaching the connector views for you.
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10
Pages: [1]   Go Up
« previous next »