« previous next »
Pages: [1]   Go Down

Author Topic: installing new upper control arms  (Read 6804 times)

Offline gold84gmc

  • Frequent Member
  • **
  • Posts: 483
installing new upper control arms
« on: October 21, 2009, 07:27:28 am »
how many pumps of grease do i put in the grease fittings on the shaft?
Logged
92 buick century custom 3.3L

Offline Flamingbig10

  • Frequent Member
  • **
  • Posts: 340
Re: installing new upper control arms
« Reply #1 on: October 21, 2009, 11:38:36 am »
last ones I did, I filled them up with grease until some started to come out
Logged

Offline gold84gmc

  • Frequent Member
  • **
  • Posts: 483
Re: installing new upper control arms
« Reply #2 on: October 21, 2009, 07:14:29 pm »
alright thanks...with the grease fitting on the ball joint, where it screws into, there isnt any threads on eather of the control arms i got, are they supposed to be like this or do i have to put my own threads?
Logged
92 buick century custom 3.3L

Offline Jim Rockford

  • Banned
  • Frequent Member
  • **
  • Posts: 358
Re: installing new upper control arms
« Reply #3 on: October 22, 2009, 07:14:52 am »
No the fitting will make its own threads. just screw it in straight. just pump grease in it till you can see the boot start to swell.
Logged
1973 k20 Camper special
1980 k20 custom deluxe
2004 Crown Vic LX sport

Offline gold84gmc

  • Frequent Member
  • **
  • Posts: 483
Re: installing new upper control arms
« Reply #4 on: October 22, 2009, 01:47:04 pm »
there aren't any threads so i cant screw it in
Logged
92 buick century custom 3.3L

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19169
Re: installing new upper control arms
« Reply #5 on: October 22, 2009, 03:25:16 pm »
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline gold84gmc

  • Frequent Member
  • **
  • Posts: 483
Re: installing new upper control arms
« Reply #6 on: October 22, 2009, 03:30:18 pm »
no the fittings are fine, where they screw into ontop of the ball joints is where there are no threads
Logged
92 buick century custom 3.3L

Offline Toolmaster

  • Administrator
  • Frequent Member
  • *****
  • Posts: 348
Re: installing new upper control arms
« Reply #7 on: October 22, 2009, 07:46:07 pm »
They could be drive-in zerks. Look and see if the have threads or are they just rings. Put one between fingernail's and twist, if it dont screw out, it's a drive-in zerk.
Logged
Hang him !!!    (Judge Roy Bean)  Looters will be shot on site !!!

Offline gold84gmc

  • Frequent Member
  • **
  • Posts: 483
Re: installing new upper control arms
« Reply #8 on: October 24, 2009, 05:51:56 pm »
so if its a drive-in zerk then do i just hit it in with a hammer?
Logged
92 buick century custom 3.3L

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19169
Re: installing new upper control arms
« Reply #9 on: October 24, 2009, 05:54:50 pm »
No! Righty tighty! Push inward with your finger while you thread it in.
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline gold84gmc

  • Frequent Member
  • **
  • Posts: 483
Re: installing new upper control arms
« Reply #10 on: October 24, 2009, 09:07:53 pm »
i did and it wouldnt go in....from what i understand a drive-in zerk doesnt have threads it has "rings" around it
Logged
92 buick century custom 3.3L

Offline Jim Rockford

  • Banned
  • Frequent Member
  • **
  • Posts: 358
Re: installing new upper control arms
« Reply #11 on: November 05, 2009, 06:27:29 am »
take a 1/4 drive socket the size of the zerk, . Then PUSH DOWN as you try and screw it in, it is a self tapping zerk,  no company takes the time to thread the BJ for the zerk. and DO NOT drive it in with a hammer. :'(

You have just been banned for 30 days for that comment.  -ADMIN
« Last Edit: November 05, 2009, 09:48:16 pm by Captkaos »
Logged
1973 k20 Camper special
1980 k20 custom deluxe
2004 Crown Vic LX sport

Offline gold84gmc

  • Frequent Member
  • **
  • Posts: 483
Re: installing new upper control arms
« Reply #12 on: November 05, 2009, 02:03:23 pm »
calm down!...not everyone is an expert with everything...and i did exactly what you said and it wouldnt go in
Logged
92 buick century custom 3.3L

Offline Jim Rockford

  • Banned
  • Frequent Member
  • **
  • Posts: 358
Re: installing new upper control arms
« Reply #13 on: November 05, 2009, 03:39:07 pm »
you might need to put some paper or something to fill up the socket a little bit to keep the zerk from going too far into the socket and not letting you apply pressure..Is the socket bottoming out on the top of the ball joint?
Logged
1973 k20 Camper special
1980 k20 custom deluxe
2004 Crown Vic LX sport

Offline gold84gmc

  • Frequent Member
  • **
  • Posts: 483
Re: installing new upper control arms
« Reply #14 on: November 05, 2009, 08:50:06 pm »
nope its not bottoming out, and i used a short socket so it wasnt going up into the socket
Logged
92 buick century custom 3.3L
Pages: [1]   Go Up
« previous next »