« previous next »
Pages: [1] 2   Go Down

Author Topic: cheap good headers?  (Read 20590 times)

Offline StuntManMike

  • Newbie
  • Posts: 12
cheap good headers?
« on: October 31, 2009, 03:28:40 am »
hi guys! i was wanted to get some opinions on some cheap headers for my 87 v10, i want to put some on but dont want to put a hole in my wallet. I went on summit racing and seen summit makes there own headers they also have some hedman and flowtec headers at a good price. I also found some hooker headers for decently cheap as well. anyone know if these opions are any good or have any suggestions? Im not looking at paying anymore than $120 for the set.
thanks guys,
Mike Felker
Logged

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19181
Re: cheap good headers?
« Reply #1 on: October 31, 2009, 08:49:58 am »
Personally I never use cheap non coated headers anymore because they rust in no time and they constantly leak. I've had good luck with some of the overseas cheapies. Is your 87 V10 a truck or blazer? 5.7 tbi? Do you have a.i.r. ? Are you looking for full length headers? Since your goal is to save $ Why do you want to run headers anyway? Do you have stock manifolds? Keep in mind you'll need an O2 sensor bung also.
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline 4x4orbust

  • Frequent Member
  • **
  • Posts: 342
Re: cheap good headers?
« Reply #2 on: October 31, 2009, 01:31:15 pm »
i have a set of hedman headers that i like.   i would not cal them cheap, but they arent too pricey.   no leaks,  and they are rusted, but not so bad as to replace them.   my $.02
Logged
1982 chevy K-10 SWB, 355 th350/np208. 2.5"lift, 33" swampers, headers/duals,  current project

Offline Chevalade

  • Frequent Member
  • **
  • Posts: 329
Re: cheap good headers?
« Reply #3 on: October 31, 2009, 06:00:53 pm »
No such thing as a cheap good header. If you plan on keeping the truck for any length of time, get a good set. It will be worth it in the long run.
Logged

Offline dunedigger

  • Frequent Member
  • **
  • Posts: 274
Re: cheap good headers?
« Reply #4 on: November 01, 2009, 01:11:42 am »
Here in michigan it seems no mater what header I buy it will rust out if I drive in the salty winters.  But I've only tried headman and dynomax so far and I hated the headmans I bought.  I've been sticking with dynomax and had good luck except one pair had the tube bent too far in front of a bolt hole and I had to grind down a end wrench to tighten that header bolt.  I'll never buy another set that isn't coated.  It seems to be worth the extra money to save replacing them so often.  I did see somewhere a piece you can put between the header and collector with an o2 bung so you don't have to weld one in.  I've never put headers on a fi motor yet.
Logged

Offline StuntManMike

  • Newbie
  • Posts: 12
Re: cheap good headers?
« Reply #5 on: November 03, 2009, 02:56:26 pm »
sorry it been awhile and didnt reply but iv been moving. thanks for all your input guys! VileZambonie it is a truck and is a 5.7 and i am looking for full headers and i do have stock manifolds. i have heard alot about rusting...and in about 10 months im going back to pittsburgh so salt will be an issue...is there anything i can coat the headers in to reduce rust if i would go with headers?
Logged

Offline Chevalade

  • Frequent Member
  • **
  • Posts: 329
Re: cheap good headers?
« Reply #6 on: November 03, 2009, 04:52:33 pm »
You can buy headers already ceramic coated. I have a set on my 81, long tubes. Cost me about $450 or $500 for them. They last well.
Logged

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19181
Re: cheap good headers?
« Reply #7 on: November 04, 2009, 07:50:06 pm »
you can get coated ones for under $300 bucks
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline dunedigger

  • Frequent Member
  • **
  • Posts: 274
Re: cheap good headers?
« Reply #8 on: November 05, 2009, 07:39:44 pm »
Yeah, not sure on price but I know my dynomax ceramic coat were less than 300
Logged

Offline jimbo

  • Registered Users
  • *
  • Posts: 113
Re: cheap good headers?
« Reply #9 on: December 03, 2009, 10:05:08 pm »
Logged

Offline lbrowne

  • Newbie
  • Posts: 65
Re: cheap good headers?
« Reply #10 on: December 28, 2009, 09:56:10 pm »
Quote from: jimbo on December 03, 2009, 10:05:08 pm
How about these?

http://www.summitracing.com/parts/SUM-G9006/

I was wondering the same thing. I've heard of people use the summit brand equipment with no issues which is usually just a re-branded product they carry. For example, those headers might actually be made by Pacesetter or Hedman.
Logged
1986 GMC Sierra Classic
My first truck! (completely stock...for now)

Offline joesgarage71

  • Wrench
  • Senior Member
  • ****
  • Posts: 1156
Re: cheap good headers?
« Reply #11 on: December 29, 2009, 10:07:17 am »
I always check the summit stuff first when making a buy. There parts are good quality and inexpensive. If there is any problem with them summitracing will back them up! Headers only last me about two-three years anyway so I buy them inexpensive.

BTW I Never use the words "cheap and good" together.
Logged
78' K-20 355/SM465/twin stick 205 6" on 36's
14 bolt FF/big bearing Dana 44 4.56 gears
92' GMC C-1500 454/4L80E/14 bolt

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19181
Re: cheap good headers?
« Reply #12 on: December 29, 2009, 10:17:14 am »
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline frogman68

  • Junior Member
  • ***
  • Posts: 773
Re: cheap good headers?
« Reply #13 on: December 29, 2009, 12:54:47 pm »
Quote from: jimbo on December 03, 2009, 10:05:08 pm
How about these?

http://www.summitracing.com/parts/SUM-G9006/

Used them on a 84 k10 manual trans and no big issues.
Hard part was getting the pipe to the rear past the cross member but the 20 ton press fixed the pipe no leaks as of yet.

For the headers , pipping and mufflers was a little less than 200 dont expect it to last but its doing the job lol
Logged

Offline 1badazz84

  • Newbie
  • Posts: 11
Re: cheap good headers?
« Reply #14 on: December 30, 2009, 08:47:05 pm »
I BOUGHT A SET FLOWTECH FOR $120.00 AT AUTO ZONE. I HAVE THEM FOR 5 MONTHS SOUNDS GOOD THEY HAVE NOT RUST BUT IM GOING TO USED HEADER WRAP FOR HEAT BUT THE DIFFENCE BETWEEN THE GOOD ONES & CHEAP ONES ARE THE DIFFERNCE GAUGE OF THE STEEL THEY USE.
Logged
Pages: [1] 2   Go Up
« previous next »