« previous next »
Pages: [1]   Go Down

Author Topic: Swap question on am465  (Read 3501 times)

Offline bake74

  • Senior Member
  • ****
  • Posts: 5871
    • Build Thread
Swap question on am465
« on: March 01, 2011, 02:41:36 pm »
     Will a sm465/np 208 from a 85 blazer bolt into a 77 k10 that had a sm 465 in it ?  I wanted to know if the linkage is the same as with the transfer case cross member, if it would be just a straight bolt in or not.  I searched but could not find an answer here, thanks in advance.   Tom
Logged
#1: The easiest and most obvious solution to any problem is 99% of the time correct.
#2: There is no such thing as impossible, it just takes longer.
  74 k10, 77k10    Tom

Offline Grim 82

  • Senior Member
  • ****
  • Posts: 1651
Re: Swap question on am465
« Reply #1 on: March 01, 2011, 03:19:29 pm »
My guess is that the crossmember location, driveshaft lengths, and t-case shifter would be different, but not sure. Do you have the t-case shifter and the driveshafts from the np208 truck? Probably simple to do, but probably not a straight bolt in...

Logged
Give a man a gun, and he might rob a bank. Give a man a bank, and he might rob the world.

Offline bake74

  • Senior Member
  • ****
  • Posts: 5871
    • Build Thread
Re: Swap question on am465
« Reply #2 on: March 01, 2011, 04:30:14 pm »
     The 85 is complete, since the 77 got it all stolen I will have to get the shifters and mounts also.
Logged
#1: The easiest and most obvious solution to any problem is 99% of the time correct.
#2: There is no such thing as impossible, it just takes longer.
  74 k10, 77k10    Tom

Offline 1980c10

  • Senior Member
  • ****
  • Posts: 1205
Re: Swap question on am465
« Reply #3 on: March 01, 2011, 05:19:20 pm »
The '85 should have a hydraulic clutch linkage the '77 is mechnical. It can be converted to hydraulic but would require some modifications. I guess it depends what parts you have. Do you have the linkage for the '77?
Logged

Offline Grim 82

  • Senior Member
  • ****
  • Posts: 1651
Re: Swap question on am465
« Reply #4 on: March 01, 2011, 06:33:33 pm »
If the 85 is complete, you should have most everything you need for the swap. As near as I know, to keep the mechanical clutch setup you would just need to swap the front clutch housing/bell housing portion on the trans with a mechanical bellcrank style one. Hydraulic would be a good upgrade though if you have all the parts.
Logged
Give a man a gun, and he might rob a bank. Give a man a bank, and he might rob the world.

Offline bake74

  • Senior Member
  • ****
  • Posts: 5871
    • Build Thread
Re: Swap question on am465
« Reply #5 on: March 02, 2011, 06:11:02 pm »
     They took the fly wheel, bell housing, trans and trsnfr case, and all the linkage, so I will have to check into going hydraulic as an upgrade or find something else.  Thanks for the answer's.
Logged
#1: The easiest and most obvious solution to any problem is 99% of the time correct.
#2: There is no such thing as impossible, it just takes longer.
  74 k10, 77k10    Tom
Pages: [1]   Go Up
« previous next »