« previous next »
Pages: [1]   Go Down

Author Topic: I need a measurement please.  (Read 2597 times)

Offline klaussk

  • Registered Users
  • *
  • Posts: 160
I need a measurement please.
« on: January 04, 2012, 11:29:44 am »
I am currently on deployment and I wanted to make a velocity stack for my carb and air cleaner. But I forgot to take the measurements when I was home on leave. I just need  the inside and outside diameter of the seat for the air cleaner on top of the carb. Its a 4160 holley 600 cfm. the same size that the stock quadrajet uses. So measuring either one would work for me. Thanks guys. I really appreciate anyone who will take these measurements for me. Its my deployment project. I need to raise the air cleaner because  I am going to build a ramair hood.
Logged
Go ahead hit it with a hammer. Theres only one level of broke.

Offline ehjorten

  • Senior Member
  • ****
  • Posts: 1242
Re: I need a measurement please.
« Reply #1 on: January 04, 2012, 01:38:11 pm »
I've got both!  Can take that measurement for you when I get home tonight.
Logged
-Erik-
1991 V3500 - Gen V TBI 454, 4L80E, NP205, 14 bolt FF, D60, 8" Lift on 35s
1977 K20 Silverado - 350, THM350, NP203, 14 bolt FF, D44, Stock Lift on 31s
1969 Chevelle Malibu Sport Coupe - EFI350, THM350
1968 Chevrolet Step-side Pickup - 300HP L6

Offline klaussk

  • Registered Users
  • *
  • Posts: 160
Re: I need a measurement please.
« Reply #2 on: January 04, 2012, 09:27:06 pm »
Thanks man. I appreciate it.
Logged
Go ahead hit it with a hammer. Theres only one level of broke.

Offline ehjorten

  • Senior Member
  • ****
  • Posts: 1242
Re: I need a measurement please.
« Reply #3 on: January 05, 2012, 07:20:53 pm »
Inside diameter is 5" and the outside diameter is 5-1/2".  Sorry for the day delay!
Logged
-Erik-
1991 V3500 - Gen V TBI 454, 4L80E, NP205, 14 bolt FF, D60, 8" Lift on 35s
1977 K20 Silverado - 350, THM350, NP203, 14 bolt FF, D44, Stock Lift on 31s
1969 Chevelle Malibu Sport Coupe - EFI350, THM350
1968 Chevrolet Step-side Pickup - 300HP L6

Offline klaussk

  • Registered Users
  • *
  • Posts: 160
Re: I need a measurement please.
« Reply #4 on: January 05, 2012, 08:49:07 pm »
thats great. Thank you very much. And that just so happens to be the perfect size to use a section from a 5 inch shell. they taper out towards the bottom ever so slightly. So I should be able to cut a perfect peice for it.
Logged
Go ahead hit it with a hammer. Theres only one level of broke.

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19180
Re: I need a measurement please.
« Reply #5 on: January 05, 2012, 08:55:11 pm »
5 1/8" is standard measurement

Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10
Pages: [1]   Go Up
« previous next »