« previous next »
Pages: [1]   Go Down

Author Topic: Bad Pulleys???  (Read 2799 times)

Offline pedigo78

  • Registered Users
  • *
  • Posts: 213
  • Big Blue
Bad Pulleys???
« on: January 15, 2013, 01:25:34 pm »
So my dad is getting my truck ready to get shipped up here to cali. with me. He says the alternator belt is whinning louder than my motor. belt is good and tight, belt is also new. I think its time for new pulleys, i have been havning problems with this in the past and breaking belts too. what do yall think
Logged
Sgt Pedigo USMC

Offline Captkaos

  • OWNER and Administrator
  • Administrator
  • Senior Member
  • *****
  • Posts: 18463
    • http://www.73-87chevytrucks.com
Re: Bad Pulleys???
« Reply #1 on: January 15, 2013, 01:38:04 pm »
Is it the belt or the alternator or waterpump making the noise?  Put some dry soap on the back and see if it stops.
Logged

Offline pedigo78

  • Registered Users
  • *
  • Posts: 213
  • Big Blue
Re: Bad Pulleys???
« Reply #2 on: January 15, 2013, 01:59:28 pm »
used a little wd40 to see what would happen, dad says it still whinning. but i do want to replace that v belt pulleys for a serp. kit
Logged
Sgt Pedigo USMC

Online ehjorten

  • Senior Member
  • ****
  • Posts: 1242
Re: Bad Pulleys???
« Reply #3 on: January 22, 2013, 03:54:02 pm »
V-belt sheaves get burnished from too much slipping of the V-belt.  Once that sheave is burnished it is best to replace it.

Sheave / Pulley...I know I know...let's not go off on that tangent.  You know what I am talking about...that round disk with the groove in it that once attached to a shaft or system of support becomes a pulley!  ;D
Logged
-Erik-
1991 V3500 - Gen V TBI 454, 4L80E, NP205, 14 bolt FF, D60, 8" Lift on 35s
1977 K20 Silverado - 350, THM350, NP203, 14 bolt FF, D44, Stock Lift on 31s
1969 Chevelle Malibu Sport Coupe - EFI350, THM350
1968 Chevrolet Step-side Pickup - 300HP L6

Offline Sartobuilt

  • Registered Users
  • *
  • Posts: 187
Re: Bad Pulleys???
« Reply #4 on: January 22, 2013, 07:19:46 pm »
If you seperated the pully apart into two pieces you would have two sheaves...LOL
Logged

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19183
Re: Bad Pulleys???
« Reply #5 on: January 22, 2013, 07:37:25 pm »
Make sure nothing is seized
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline pedigo78

  • Registered Users
  • *
  • Posts: 213
  • Big Blue
Re: Bad Pulleys???
« Reply #6 on: January 24, 2013, 01:24:12 pm »
Cool, well big blue should be here in about 10 days, so after i drive the shoot out of it for some enjoyment, ill look into everything.
Logged
Sgt Pedigo USMC
Pages: [1]   Go Up
« previous next »