« previous next »
Pages: 1 2 3 [4] 5 6 ... 11   Go Down

Author Topic: Homemade Headers  (Read 116315 times)

Offline jonkmbll89

  • Registered Users
  • *
  • Posts: 216
  • 85 Chevy Silverado C10 swb 5.7/350
Re: Homemade Headers
« Reply #45 on: December 22, 2007, 06:41:38 pm »
Quote from: 123 pugsy on December 21, 2007, 05:14:49 am
Thanks.

Its going so slowwwwwwww. :P

The last set I did was quicker as all I was concerned about was clearing the frame and not the tube lenghts.

Pugsy, you do good work. :o
Logged
GET IN, SIT DOWN, SHUTUP, AND HANG ON

Offline 123 pugsy

  • Junior Member
  • ***
  • Posts: 925
Re: Homemade Headers
« Reply #46 on: December 22, 2007, 08:36:07 pm »
Thanks. I should have pics tommorow of 1 side pretty much done. I don't know how its going in though, may have to lift the motor.... :P
Logged
Pugsy
76 C10 LWB
TPI 350

Offline 123 pugsy

  • Junior Member
  • ***
  • Posts: 925
Re: Homemade Headers
« Reply #47 on: December 23, 2007, 05:45:38 pm »
Got the collector cut and welded to the header.
I just got to check the fit now and then finish welding the tubes to the flanges.


Logged
Pugsy
76 C10 LWB
TPI 350

Offline 123 pugsy

  • Junior Member
  • ***
  • Posts: 925
Re: Homemade Headers
« Reply #48 on: December 23, 2007, 05:46:58 pm »
A couple more pics.


Logged
Pugsy
76 C10 LWB
TPI 350

Offline JJSZABO

  • Senior Member
  • ****
  • Posts: 1009
Re: Homemade Headers
« Reply #49 on: December 23, 2007, 06:53:38 pm »
WOW - I can't say enough - WOW.  Great work. 

Thanks for the pictures pugsy and vile.  I am thinking of making an engine stand, when I am done with this truck.
Logged
Jeff

86 Chevy C-10
350, TH400
Ex father and son project (son lost interest)

Son regained interest when truck was almost completed

Offline jonkmbll89

  • Registered Users
  • *
  • Posts: 216
  • 85 Chevy Silverado C10 swb 5.7/350
Re: Homemade Headers
« Reply #50 on: December 23, 2007, 06:57:17 pm »
I don't care what anybody says, that is fine work. ;D
« Last Edit: December 24, 2007, 06:06:16 pm by jonkmbll89 »
Logged
GET IN, SIT DOWN, SHUTUP, AND HANG ON

Online VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19170
Re: Homemade Headers
« Reply #51 on: December 24, 2007, 08:34:27 am »
Pugsy, are you going to run your wires forward and then along the valve cover? Looks great! Very unique!
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline 87GMC2WD

  • Registered Users
  • *
  • Posts: 152
Re: Homemade Headers
« Reply #52 on: December 24, 2007, 08:41:17 am »
amazing, ive fabricated snowblower holders and all sorts of trailers and home-made pullers, but i dont think i could ever do this. Dont know if id have the pateince.
Logged

Offline 123 pugsy

  • Junior Member
  • ***
  • Posts: 925
Re: Homemade Headers
« Reply #53 on: December 24, 2007, 09:24:53 am »
Quote from: JJSZABO on December 23, 2007, 06:53:38 pm
WOW - I can't say enough - WOW.  Great work. 

Thanks for the pictures pugsy and vile.  I am thinking of making an engine stand, when I am done with this truck.

Quote from: jonkmbll89 on December 23, 2007, 06:57:17 pm
I don't care what anybody says, that is dam fine work. ;D

Quote from: 87GMC2WD on December 24, 2007, 08:41:17 am
amazing, ive fabricated snowblower holders and all sorts of trailers and home-made pullers, but i dont think i could ever do this. Dont know if id have the pateince.


Thanks guys. I still have to find the patience to finish the other side along with 1 more exhaust pipe as well. :o
Logged
Pugsy
76 C10 LWB
TPI 350

Offline 123 pugsy

  • Junior Member
  • ***
  • Posts: 925
Re: Homemade Headers
« Reply #54 on: December 24, 2007, 09:29:44 am »
Quote from: VileZambonie on December 24, 2007, 08:34:27 am
Pugsy, are you going to run your wires forward and then along the valve cover? Looks great! Very unique!

Thanks for the reminder. I've got to figure out the wires before ceramic coating. I may weld tabs to screw wire holders to if needed to keep them away.
Logged
Pugsy
76 C10 LWB
TPI 350

Offline 123 pugsy

  • Junior Member
  • ***
  • Posts: 925
Re: Homemade Headers
« Reply #55 on: December 28, 2007, 09:42:42 am »
I ground down an 18mm s/s nut with a zipcut disc to use as an o2 sensor bung.
Logged
Pugsy
76 C10 LWB
TPI 350

Offline 123 pugsy

  • Junior Member
  • ***
  • Posts: 925
Re: Homemade Headers
« Reply #56 on: December 28, 2007, 09:48:27 am »
Round peg in a square hole. I had to stretch the corners out with a hammer and punch.
Logged
Pugsy
76 C10 LWB
TPI 350

Online VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19170
Re: Homemade Headers
« Reply #57 on: December 28, 2007, 11:11:05 am »
Very cool Pugsy!
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline ccz145a

  • Senior Member
  • ****
  • Posts: 1393
Re: Homemade Headers
« Reply #58 on: December 28, 2007, 11:31:52 am »
Nice work!
Logged
1975 C10 Silverado LWB, 454CID, TH400, 10bolt 3.42
11MPG Downhill w/tailwind (but there ain't no hills here)

Offline jonkmbll89

  • Registered Users
  • *
  • Posts: 216
  • 85 Chevy Silverado C10 swb 5.7/350
Re: Homemade Headers
« Reply #59 on: December 28, 2007, 06:15:52 pm »
Nice job.
Logged
GET IN, SIT DOWN, SHUTUP, AND HANG ON
Pages: 1 2 3 [4] 5 6 ... 11   Go Up
« previous next »