« previous next »
Pages: [1]   Go Down

Author Topic: Going from "roll up" to power windows  (Read 4481 times)

Offline bigkountry

  • Frequent Member
  • **
  • Posts: 453
Going from "roll up" to power windows
« on: June 09, 2008, 09:35:45 am »
I just picked up a set of mint doors from a friend for $50 they are electric though. The motors and wiring are intact with the doors, what am I looking at parts wise to make the swap?

Thanks
Logged
81 Scottsdale K10 "Under construction"

Offline Captkaos

  • OWNER and Administrator
  • Administrator
  • Senior Member
  • *****
  • Posts: 18462
    • http://www.73-87chevytrucks.com
Re: Going from "roll up" to power windows
« Reply #1 on: June 09, 2008, 10:07:19 am »
As far as the doors go, you can just bolt them up.  The wiring has to pass through the door frame so you are going to have to drill a hole and route the harness into the cab.  Did you get the harness that goes into the cab?
Logged

Offline bigkountry

  • Frequent Member
  • **
  • Posts: 453
Re: Going from "roll up" to power windows
« Reply #2 on: June 09, 2008, 10:14:34 am »
Sadly no, he junked the truck a while back and had these laying around. I have no clue whats' what on electric windows, only had the manuals til now...even my 01 Silvy has manuals..lol

Something new to learn I guess, I do know where an 85 "power" cab is sitting with all wiring intact, might just have to go look into it.

Thanks
Logged
81 Scottsdale K10 "Under construction"

Offline Blazin

  • Blazin new trails!
  • Senior Member
  • ****
  • Posts: 6130
Re: Going from "roll up" to power windows
« Reply #3 on: June 09, 2008, 10:30:26 am »
There is a wire harness that plugs into the face of the fuse box, & runs out to both doors. Take note of where the holes are in the door jamb. Then when you get your doors off if you look real close you will see where it has little a dimple to drill your pilot hole for your hole saw. and two little dimples above and below to drill for your screws.
Logged
Some people are like Slinkies. Not really good for anything, but they still bring a smile to your face when you push them down a flight of stairs

Offline Captkaos

  • OWNER and Administrator
  • Administrator
  • Senior Member
  • *****
  • Posts: 18462
    • http://www.73-87chevytrucks.com
Re: Going from "roll up" to power windows
« Reply #4 on: June 09, 2008, 11:09:55 am »
Logged

Offline werewolfx13

  • Site Supporters
  • Junior Member
  • ******
  • Posts: 841
Re: Going from "roll up" to power windows
« Reply #5 on: June 15, 2008, 03:14:08 pm »
I have one question for you...Why?

I hate power windows...except the power windows on my '63 riviera..Those are neat cause you can roll the windows up and down without turning the key on..that and its a 2 door car with 4 power windows..
Logged
Chris
'83 Chevy c10 Silverado SWB
'76 Chevy k20 LWB 6.5'x8' Flatbed
“I know that you believe you understand what you think I said, but I'm not sure you realize that what you heard is not what I meant.”

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19182
Re: Going from "roll up" to power windows
« Reply #6 on: June 15, 2008, 06:01:30 pm »
power windows are nice in that you can open the passenger side from the drivers door and if they work correctly are a nice option. I have a set to put back in my blue truck but haven't had time but I will!
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠¯¯¯¯¯'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline werewolfx13

  • Site Supporters
  • Junior Member
  • ******
  • Posts: 841
Re: Going from "roll up" to power windows
« Reply #7 on: June 15, 2008, 07:48:36 pm »
I guess I can see the passenger side, there have been a few times where that would have been handy..but I'd rather keep the drivers side manual..but thats probably just me..
Logged
Chris
'83 Chevy c10 Silverado SWB
'76 Chevy k20 LWB 6.5'x8' Flatbed
“I know that you believe you understand what you think I said, but I'm not sure you realize that what you heard is not what I meant.”

Offline bigkountry

  • Frequent Member
  • **
  • Posts: 453
Re: Going from "roll up" to power windows
« Reply #8 on: June 16, 2008, 03:59:23 pm »
I just got them on the cheap from a buddy and thought it would be something nice for the ol girl. Plus my wife hates to roll down windows..lol
Logged
81 Scottsdale K10 "Under construction"
Pages: [1]   Go Up
« previous next »