« previous next »
Pages: [1] 2   Go Down

Author Topic: bed project  (Read 9236 times)

Offline lpapa15

  • Newbie
  • Posts: 56
  • 1979 k10 silverado
bed project
« on: October 25, 2010, 01:54:08 pm »
Has anyone replaced the side of a bed?  I need to replace the entire side of my bed and i want to know how hard it will be knowing that there is welding involved..

Can the side of a shortbed 79 fit and swap with a shortbed of an 85?

Please help...
Logged

Offline Captkaos

  • OWNER and Administrator
  • Administrator
  • Senior Member
  • *****
  • Posts: 18464
    • http://www.73-87chevytrucks.com
Re: bed project
« Reply #1 on: October 25, 2010, 04:41:26 pm »
There are spot welds down the bed floor to the inner bedside.  Hard depends on you experience, I would say it would be harder than say removing a rusty rocker.

Which side?  Technically it should work.
Logged

Offline lpapa15

  • Newbie
  • Posts: 56
  • 1979 k10 silverado
Re: bed project
« Reply #2 on: October 26, 2010, 12:07:22 am »
Driver's side.
Logged

Offline Captkaos

  • OWNER and Administrator
  • Administrator
  • Senior Member
  • *****
  • Posts: 18464
    • http://www.73-87chevytrucks.com
Re: bed project
« Reply #3 on: October 26, 2010, 10:11:09 am »
If it is the side without the filler bulge is should work fine.
Logged

Offline onelow84

  • Registered Users
  • *
  • Posts: 113
Re: bed project
« Reply #4 on: November 21, 2010, 11:11:26 am »
just took my passenger bedside off to replace the front panel and there were no welds. It took about two hours to take off the whole passenger side, clean and repaint where everything bolts together and replace the front panel and put the bedside back on. it was my first time doing this and the bed was on a lift not on the truck. pretty easy and straight forward job. hope this helps. also only needed a
phillips screw driver and 1/2 and 9/16 sockets on an air ratchet
Logged

Offline Blazin

  • Blazin new trails!
  • Senior Member
  • ****
  • Posts: 6130
Re: bed project
« Reply #5 on: November 21, 2010, 11:59:41 am »
The only welds should be the rear bed post where tailgate shuts. It has two spot welds at the base of it to the floor. Other than that the whole side unbolts from the floor, and front panel.
Logged
Some people are like Slinkies. Not really good for anything, but they still bring a smile to your face when you push them down a flight of stairs

Offline onelow84

  • Registered Users
  • *
  • Posts: 113
Re: bed project
« Reply #6 on: November 21, 2010, 02:12:31 pm »
sorry just saw that you have a blazer and not a pick up...
Logged

Offline Blazin

  • Blazin new trails!
  • Senior Member
  • ****
  • Posts: 6130
Re: bed project
« Reply #7 on: November 21, 2010, 03:51:36 pm »
onelow84 just curious, how did you come up with a Blazer?
Logged
Some people are like Slinkies. Not really good for anything, but they still bring a smile to your face when you push them down a flight of stairs

Offline topp

  • Frequent Member
  • **
  • Posts: 498
Re: bed project
« Reply #8 on: November 21, 2010, 04:26:32 pm »
Quote from: Blazin on November 21, 2010, 03:51:36 pm
onelow84 just curious, how did you come up with a Blazer?

Look at the avatar...
Logged
'90 Suburban TBI 350

Offline VileZambonie

  • Global Moderator
  • Senior Member
  • *****
  • Posts: 19184
Re: bed project
« Reply #9 on: November 21, 2010, 04:40:14 pm »
I'm confused
Logged
,                           ___ 
                         /  _ _ _\_
              ⌠ŻŻŻŻŻ'   [☼===☼]
              `()_);-;()_)--o--)_)

74 GMC, 75 K5, 84 GMC, 85 K20, 86 k20, 79 K10

Offline Blazin

  • Blazin new trails!
  • Senior Member
  • ****
  • Posts: 6130
Re: bed project
« Reply #10 on: November 21, 2010, 04:50:12 pm »
Looks like a 79 K10 to me!
He is asking about short bed bed sides in his post as well.
« Last Edit: November 21, 2010, 04:52:01 pm by Blazin »
Logged
Some people are like Slinkies. Not really good for anything, but they still bring a smile to your face when you push them down a flight of stairs

Offline onelow84

  • Registered Users
  • *
  • Posts: 113
Re: bed project
« Reply #11 on: November 21, 2010, 05:48:11 pm »
Nevermind...Its been a long day, was thrown off by the welding on part. Am i wrong that if your replacing an entire bedside there is no welds. mine just unbolted.
Logged

Offline Blazin

  • Blazin new trails!
  • Senior Member
  • ****
  • Posts: 6130
Re: bed project
« Reply #12 on: November 21, 2010, 07:33:57 pm »
No problem, we all have them.  :o
There should be two short welds right at the base of the rear post where it meets the floor just inside the gate.
Logged
Some people are like Slinkies. Not really good for anything, but they still bring a smile to your face when you push them down a flight of stairs

Offline onelow84

  • Registered Users
  • *
  • Posts: 113
Re: bed project
« Reply #13 on: November 21, 2010, 07:38:05 pm »
maybe mine has been off/replaced before and noone welded it back up. looked to have factory seam sealer every where.
Logged

Offline fitz

  • Senior Member
  • ****
  • Posts: 2085
Re: bed project
« Reply #14 on: November 21, 2010, 10:09:53 pm »
Quote from: onelow84 on November 21, 2010, 07:38:05 pm
maybe mine has been off/replaced before and noone welded it back up.

Maybe it was 1 of my welds and it just didn't hold. I'm still in the learning stages with my mig.
Logged
Pages: [1] 2   Go Up
« previous next »